Tuesday, May 18, 2010

The Knuckledragger Takes It's First Breath

Not without some monkeying around, though. (Monkeying around/ Knuckledragger; get it?)

Last fall I finished up the build on my re-creation of a 1950's drag bike, "The Knuckledragger." I did take one stab at starting the bike at that time, but my tendency towards, shall we say, frugality, foiled that attempt. I pulled the battery out of one of my cars to power the roller starter. Unfortunately a weaker than expected battery and a lot of compression conspired to "shoot" the rollers out from under the rear wheel on each attempt.

Then, being the skinflint that I am, I chose to wait till spring to purchase a new battery. Two actually. After conferring with the builder of the rollers, I opted to run them on 24 volts rather than 12.

So, with a pair of 795 cold cranking amp batteries, and the help of our son Joe, it was time to see if the bike would actually run. The first glitch came soon enough. In the excitement of the moment, I forgot to rewire the solenoid on the rollers. I knew better of course, as evidenced by the fact that I realized immediately what I had done wrong when the contacts welded themselves, leaving me helplessly holding the bike up as the the rollers (and the rear wheel of the bike) spun uncontrollably. Luckily, Joe is a veteran of dragbike stuff not always behaving as planned. Without hesitation he started to unhook a battery cable. Hmm. Maybe I should have actually installed that 1/4 turn quick disconnect that I had left over from an earlier drag bike starter rather than just bringing it along.

No problem, at least no problem a quick trip to the local auto parts store for a new $36 solenoid wouldn't solve. With the new solenoid AND the quick disconnect installed, we were ready for round two.



Bike on the rollers, a squirt of raw gas into each carb (in case the alcohol doesn't want to light), high gear, rear wheel spinning, dump the clutch, engine spinning, and.... nothing!

Now what? Not even a pop or backfire. Must not have spark. We pull the plugs and ground them so we can check for spark. Fire up the rollers again, and sure enough, no spark. And its a new magneto! Wait, could I have wired the kill switch backward? With the engine still turning over, I flip the switch back and forth, and low and behold we get spark.

Better check that switch with an ohm meter; I can't believe I wired it backward! Well.... no. Its wired correctly, but it is intermittent. One time you flip it, and it makes contact, the next time it doesn't. Not a very good situation for a supposed safety feature! For now we'll just disconnect the switch from the mag and substitute a blade from a feeler gauge to work as a shut off switch. Besides, we have the front wheel against the building to prevent any really serious surprises.

So, we go through the whole drill again. Bike on the rollers, high gear, rear wheel spinning, dump the clutch, engine spinning, and.... it lives! And not half bad at that. I fully expected to have to do some adjusting on the low speed in order to even get the bike to idle, but I was wrong. It idled and took throttle just fine. But The Knuckledragger had one more monkey wrench to throw at us. No oil pressure.

This was not a total surprise. I had my doubts about the ability of the tiny little pre 1940 pump to pull oil uphill from the trans case, especially at the odd angle it was situated in the VL frame. In fact that is the reason I had a pressure gauge temporarily mounted. Despite a couple attempts at priming the pump, it looks like a separate oil tank is going to be in order. I left a tab on the back side of the seat post for just such a situation.

All in all, I have to admit I am quite pleased. It was fun to monkey around on a drag bike with Joe again (he started drag racing at the age of 15, if memory serves). And best of all, The Knuckledragger runs!

Tuesday, May 11, 2010

What are YOU Missing?

One of the blogs that I follow had a post today which reminded me of something that struck me during the preaching at my Church this past Sunday. I had planned a short post about this "Eureka" moment, but had not found the time yet.

The post I read contained an illustration that likely many of you have heard before; I certainly had. It speaks of how a baby is all cute and cuddly and lovable and basically helpless. But then it goes on to say how that same baby, if he grows older, but never matures, is no longer so cute and cuddly. If he were to reach the age of, say 21, and still cannot provide for himself, cannot clean up after himself, and is still just as helpless as when a baby, and this is all by his own choice, then one might be tempted to call him some sort of monster.

The analogy is that of the "Christian" who never grows up. Still no spiritual growth after 5, 10, 25 years of having a testimony of salvation. Never even read the Bible all the way through. This was what brought to mind last Sunday's sermon.

I don't recall now exactly what the statement was that my pastor made. But I do remember that what he said immediately brought to mind a verse of scripture. And I had the feeling that he was alluding to that verse without stating it specifically. I even remember thinking that if I had been preaching, I would have felt compelled to either read or point out the verse, because if someone was not familiar with the Bible, they would not get the connection; not get the full meaning.

Then it hit me. If you are not thoroughly familiar with the Bible, you are missing a big chunk of every sermon you might hear.

John 14:26 "But the Comforter, which is the holy Ghost, whom the Father will send in my Name, he shall teach you all things, and bring all things to your remembrance, which I have told you." (1599 Geneva Bible)

I don't think I am taking this verse out of context by taking this from it: it is the Holy Spirit that brings to our memory scriptures when needed. The problem is, you cannot remember what you do not know.

So, if you call yourself a Christian, isn't it about time that you grow up? You have no idea of all that you are missing.

Friday, April 30, 2010

Declaring God's Glory in Our Old Age

This Psalm was written by David during his old age as evidenced by verse 18; " Now also when I am old and greyheaded...." Old and grey headed: that seems to describe an awful lot of my friends these days. It describes nearly everyone who attended the service at the rest home where I brought this message recently. Old and grey headed also describes me, and if it describes you, that means this Psalm should be particularly applicable to us.

Note that David begins by stating that he puts his trust in the LORD Jehovah. He calls on the LORD for deliverance, and reaffirms that God is his rock and strong fortress. Each of us likewise needs to trust in the LORD as our fortress; our place of safety during the storms of life.

When David considers all that the LORD has brought him through, all the trials and tribulations that God has delivered him from, it inevitably leads him to verse 8; "Let my mouth be filled with thy praise and with thy honour all the day."

When we look back on our lives and consider how God has been our strong refuge and brought us safely through so many troubles, how can it help but bring us to the same point? How can we help but say with David "Let my mouth be filled with thy praise and with thy honour all the day."

In verse 9 David implores the Lord: "Cast me not off in the time of old age; forsake me not when my strength faileth." You see, our trials in this life are not over once we reach old age. In fact, some of you may attest that the testing becomes more severe. The solution is the same as that found by David and stated in verse 14; "But I will hope continually, and will yet praise thee more and more."

In verses 15-16 David says, "My mouth shall shew forth thy righteousness and thy salvation all the day; for I know not the numbers thereof. I will go in the strength of the Lord GOD: I will make mention of thy righteousness, even of thine only." Truly, it is Christ's righteousness that we must rely on, for as the Bible tells us, our own righteousness is like filthy rags. Because it is only Christ's righteousness that is sufficient, it follows that salvation can only be found in Christ. Once we have a proper appreciation for that, how can we help but praise God more and more, declaring his righteousness all the day!

Now we come to verse 18, the key verse for this post. "Now also when I am old and greyheaded, O God, forsake me not; until I have shewed thy strength unto this generation, and thy power to every one that is to come." What could be a better way to glorify God, than to testify, during our old age, of all the wondrous works that God has done in our lives!

Looking back, it is easy to see how the Lord has been with us from the very beginning of our lives. As it says in this psalm, God has supported us since the time we were in the womb. Every incident, every episode in our lives has worked together to lead us to the point where he saved us. And what a great salvation! The Lord not only saved us from the life of sin that we each would have inevitably continued in, if left to our own devices, but he also saved us to a glorious eternity with him.

As the potter, God continues to form us into the vessels as he chooses.
What he has done for each of us is just one small example of God's strength and power. We should delight in declaring it to this generation and the generations to follow!

Wednesday, April 28, 2010

Prepping Knuck Heads for Big Valves

I intended to post something entirely different, but at the moment, Blogger is not letting me cut and paste, so rather than rewriting something I have saved in another program, I will do something fresh.

Some time ago I started a series on installing bigger intake valves in a Knuckle head. This will be the second part of that series. When I left off, I had finished installing new exhaust seats. The seats from Rowe machine nicely (something that cannot be said for the 60+ year work hardened original seats. This also allows you to set the stem protrusion of the new valves, avoiding mis-matched depths.

If the intake nipples were removed for replacement (and in most cases they should be), now is the time to re-install them. I like to use JB Weld on the threads of the nipples, along with a stock type rivet. The epoxy is particularly important when porting, since some of the inner threads inevitably will be ground away. Here's a tip: from here on out, keep a set of used intake nuts screwed on to the nipples to protect those nice new threads.

Now that the new seats and intake nipples are installed, it is time for porting work, if you plan to do so. Doing this before new guides are installed allows you to do the best possible job. Disregarding the area just below the seat and the short side radius, the remainder of both ports should be shaped and finished as per the final product. I like a 50 grit on the intake, and a polished exhaust. However if the exhaust port is to get a thermal barrier coating, there is no point in spending extra time doing a fine polish.

With the majority of the porting work done, it is time to paint the heads. This needs to happen before guide installation, since the spring cups are held in by the valve guides. For a stock look, I use a semi-gloss black, and bake it on at about 200 degrees. Many of the hi temp paints available need this heat cycle to enable them to stand up to standard parts wash fluid. Nothing worse than keeping the new paint looking good through the whole process, only to have it get sticky and wipe off during the final wash prior to final assembly.

While the paint is drying on the heads, it is a good time to make sure the spring cups are ready to go. Often you will find a small crack just below the return tube. Be sure to weld these before going any further. Next, all of the gasket surfaces on the cups should be attended to. I use several purpose built forms along with a small hammer to return them to their original shapes. Don't forget to re-flatten the bottom portion that the guide will seal against. Once the cups are all in shape, they can be Parkerized if you are going for a stock look.

Guide installation, cutting the seats, and final porting work will be covered in the next installment.

Thursday, April 22, 2010

Green Again

On the one year anniversary of the post that I have written which received more comments than any other, I wanted to do something special. That year old post was a humorous look at my disdain for the false religion variously known as Global Warming, Ecology, Mother Earth, or simply the Green Movement. There were a total of about 30 comments, of which over 2/3 had to be deleted because they were simply vile and/or blasphemous. It certainly went a long way toward confirming my suspicion that the Green Movement is a religion. I attacked their religion, and so they attacked mine. That Global Warming is a faith based religion has been confirmed by the fact that it has lost little steam despite the fact that it's prophets with their own Urim and Thummim (computer climate models) have been shown to be liars. And let's not forget their high priest, Al Gore. On second thought, let's try to forget him!



As I said, I wanted to so something special....but there is just not enough time. I toyed with the idea of getting someone to photograph me doing a smokey burnout on a Harley, but the logistics just were not there, one reason being I have been too busy in the shop to rouse my bike out of its winter sleep. I'll have to settle for this.

Above is a 15 year old picture of me heating the 10 inch slick on my last dragbike, "The White Knuckle Express" The bike was a 120 cubic inch Knuckle with a centrifugal supercharger running 20 psi boost and producing over 200 horsepower.

Note that in the photo, my friend, Krazy Karl, has been all but rendered invisible due to tire smoke. It is quite possible that the ecology of that little plot of land in western Minnesota has yet to recover from the combination of noxious tire smoke and fumes from 120 octane racing gas. I know Karl has never been the same.

Tuesday, April 13, 2010

New, Stronger Cylinders for Your Knuck


I received a set of S&S/Flathead Power 74 inch Knuckle cylinders into the shop last week, and thought there may be an interest in some comparison shots. The black powder-coating on the S&S cylinder on the left is a little too glossy for my taste, but will doubtless hold up well.













A nice touch is the cast in emblem which suggests (but does not copy) the original's MC (Milwaukee Casting) badge









Cast in number plate also pay tribute to the original, though on the Flathead Power cylinder the large "F" corresponds to Front cylinder. Note the crack in the spigot on the stock cylinder.


Even the pistons that come with the cylinders have a dome that is reminiscent of their vintage counterpart. On left is the new S&S cast 74" piston, on the right an English made replacement piston from back in the day.

Currently the S&S suggested retail for a set of these cylinders is $980 with pistons, or $850 for cylinders alone. Not cheap by any means, but certainly a worthwhile investment if you plan serious performance modifications.

Saturday, April 3, 2010

Islam, Terrorism, Hutaree, and Westboro Baptist

For the last nine years I have been hearing something similar to this:
If it is a peaceful religion, and the terrorists are misguided, then why do we not hear an outcry from all those peaceful Muslims condemning the actions of those who have "hijacked" Islam?

Well, that's a pretty good question, and so I decided to add my voice to the outcry of genuine Christians condemning a couple of groups that have been in the news lately.

The first group is the so called "christian militia" called Hutaree. If what the media is reporting is true; that this group planned to kill police officers and then bomb more officers at the ensuing funeral hoping to spark an uprising, then there can be no doubt that this group is NOT Christian. In fact they have much more in common with a cult that was based around Charles Manson, than with Christians. Remember, Manson had a similar plan to spark an uprising.

The second group has been in and out of the news for the last several years, and never fails to make me shake my head. That group of course is the Westboro Baptist Church. As a Baptist myself, this one is particularly painful to me. I wince every time I hear the name Baptist in the middle of their name. This is the group that has made a name for itself by going to funerals of servicemen who were killed in action and insulting the dead and their families.

There is one thing that I would like to clarify for anyone reading this who is not familiar with the Baptist faith. Baptist churches are all independent. It is not a denomination in the sense that Baptist churches are not under the control or even influence of any national, let alone worldwide organization. Some Baptist churches are members of associations or conventions into which they have voluntarily joined together to accomplish common goals. Many other Baptist churches remain even more independent by not belonging to any type of association. I trust that if the Westboro bunch had been a member of any association, they would have found themselves out on their ear a long time ago.

The Westboro bunch seems to have one common theme running throughout all of their literature: God Hates. God hates fags, God hates America, God hates Israel, God hates the World - no I am not kidding, you can find each of these slogans on their website. I believe they missed one though: God hates false prophets. Fred Phelps, the founder of the Westboro group, has said " The Antichrist Bloody Beast Obama is going to become king of the world." and "Then Obama will lead the nations against Jerusalem to battle." Surely a Biblical scholar such as Phelps will embrace the Old Testament fate of one who's prophecies do not come to pass. We should not have long to wait to see if Fred really is a prophet.

Matthew 5:43-47 Ye have heard that it hath been said, Thou shalt love thy neighbour, and hate thine enemy. But I say unto you, Love your enemies, bless them that curse you, do good to them that hate you, and pray for them which despitefully use you, and persecute you; That ye may be the children of your Father which is in heaven: for he maketh his sun to rise on the evil and on the good, and sendeth rain on the just and on the unjust. For if ye love them which love you, what reward have ye? do not even the publicans the same? And if ye salute your brethren only, what do ye more than others? do not even the publicans so?

You'll have to excuse me now. I have to go pray for all the groups I just mentioned in this post!