Now, now, now ...those are not swear words, though many mechanic has used them in a tone that would imply that they are.
Introduced in 1953 to replace the ill fated Panhead "hydraulic in the top of the pushrod", certainly the 17920-53A was an big improvement since in 30+ years of wrenching I have yet to see its predecessor in working condition. I did actually meet a man once who claimed that he had a working set in his motor, but I could not verify that he was not either deaf or a liar. But I digress...
So, what is the first thing to do when you find yourself with noisy hydraulic lifters? Adjust them of course. And if that doesn't work, you adjust them again ....and yet again. After one finally realizes that further adjustment is little more than wishful thinking bordering on the vain repetition of the prayers of the heathen, then what?
Now, we have all seen Shovelhead hydraulic lifters that function flawlessly; quiet and trouble free. Common sense would tell us that for the most part this would be the norm, after all, the factory used them for over 30 years. Somehow, though, it is the ones that are noisy that stick in our memory. To be fair, a number of those that seem to be problematic are not to blame themselves, but take on the role of scape goat for other engine parts.
Low oil pressure is the first logical root cause to examine before condemning the hydraulic unit. Most who have been around Shovelheads for any time know to keep an eye on the tappet screen, since all the oil to the lifters must pass through it (hence its name). Debris plugging this small screen can definitely make for some noisy hydraulics, though the type of debris and the amount of time it took to accumulate may also indicate larger problems. Remember, the tappet screen is downstream from the gauge or sender, so you could have a good oil pressure reading, but still not enough pressure at the lifter.
The oil pump itself could also be the culprit, but there again, excess wear could itself be a symptom of worn out parts serving up a metallic oil soup. And then there are the bushings.... Oil pressure will seek the easiest path to relieve itself. Fortunately there are only a few bushings in a Shovelhead motor that are subject to pressure, those being the pinion bushing and the rocker bushings. Now lifter noise in later Shovels with the multi stage oil pumps should not be affected much by loose clearance between the pinion shaft and bushing, since the pump is designed such that it must build pressure against the top end (hydraulic lifters and rocker arms) before the pressure relief valve opens enough to supply oil to the bottom end via the pinion bushing. However, badly worn rocker bushings could still bleed off enough pressure to effectively disable the hydraulic lifters.
But what if you have good oil pressure, the rest of your engine is in good shape, and you still have noisy hydraulics? Well, maybe it's time to revisit that adjustment one last time.
First of all, I prefer to bring the engine to TDC on the compression stroke for one cylinder, and adjust both lifters for that cylinder at that point. I'll assume you can find that place in your engine's rotation. At that point the '59 to '69 FL/FLH-1200 Service Manual tells us to loosen (shorten) the pushrod until we have noticeable shake, and then extend it again until the shake is just taken up (just before it starts to compress the hydraulic unit). From that point we are to extend the pushrod 4 full turns. Fine. I have use that adjustment many, many times with good results.
Now lets look at the '70 to Early '78 FL/FLH/FX/FXE/FXS-1200 Manual. Here we find two methods. One, called the "wet" method is identical to the one we just described from the '59-'69 Manual. The other, called the "dry" method involves removing the hydraulics from the lifter, pulling the two halves apart, and cleaning out the oil (best accomplished with some spray brake parts cleaner or the equivalent). With the hydraulics cleaned of oil, we are instructed to extend the pushrod past the point where the shake is removed and all the way until the hydraulic unit is bottomed out. At this point, extending the pushrod length any further would begin to lift the valve. Here we are instructed to shorten the pushrod by exactly 1-3/4 turns. Again, I have used that adjustment many, many times with good results.
On to the '78-1/2 to '84 1200/1340cc 4 Speed Manual. Here we find the old tried and true "wet" method to be missing in action. And if that is not enough, the dry method has changed just enough to be barely noticeable (I just noticed it this summer after 30 years of valve adjustments). Now we are to follow the same procedure as the "dry" method from the '70-'78 Manual, but instead of 1-3/4 turns up from the hydraulic being bottomed out, now it calls out 1-1/2 turns. Hmm. Do I need to say it? Certainly I have used this adjustment many, many times (depending on which manual I grabbed) with good results.
But here is the interesting thing: for years I assumed that 4 turns down on a wet lifter would result in the exact same adjustment as 1-1/2 (or 1-3/4) turns up on a dry lifter. It does not! In fact, if it were not the for the 1-1/2 vs 1-3/4 discrepancy, I may have never realized this. As it turns out, it takes about 8 full turns to collapse a Shovel hydraulic from its "wet" starting point to its "dry" starting point. That means that using the "wet' adjustment method results in a hydraulic that is 4 turns up from bottomed out rather than the 1-1/2 or 1-3/4 turn up from the dry method.
[2018 Update: If the range of adjustments listed above are not enough to convince you of the relative lack of importance as to the "exact" point in the lifter's travel, I have to add one more to the list. While researching a totally unrelated issue I ran across this in Harley's "Shop Dope" publication from February 16, 1953. This gives the recommended adjustment as 5 full turns down on a wet lifter. If I count correctly, that comes to a total of four different factory settings for that lifter!]
Obviously the wet method is much less time consuming if you have no other reason to completely remove the hydraulic units from the engine, but it looks as though extending the pushrods 8-1/4 to 8-1/2 might be in order (assuming the factory had good reason to go to a tighter adjustment in later years). But it also becomes obvious that precise adjustment is not critical if all else is as it should be. So next time you adjust your lifters don't sweat it if your wrench slips and you think you may have gotten a half turn off. If its still noisy, better to spend your time investigating whether it is an engine problem or just bad lifters.
Saturday, November 24, 2012
Monday, November 5, 2012
Old Letters - Second Time Around
Generally speaking, I do not recycle my previous blog posts, but with the election tomorrow (finally!) I thought this a good time to make an exception. Since this was originally posted in January of this year, one can appreciate how much the fever pitch of the rhetoric has accelerated in the interval. Whether the turmoil dies down after the election or not remains to be seen, however, by way of a second century letter, I would like to share a comforting thought or two. So, without further fanfare:
For those who pay attention to such things, we are in the midst of the political season, if indeed that season can be said to have a beginning or end anymore. Nevertheless, it cannot help but to wear on the mind, and as often as not, leave one in despair over the future of our nation. The rhetoric only promises to increase in volume and pitch until at least November.
That is why I found myself somewhat chastised, yet at the same time encouraged, by my discovery of a letter written somewhere between 130 and 200 A.D. by one identifying himself as Mathetes to a person named Diognetus. Of course I did not stumble on it as though it were a root across my path as I explored the jungle that is the Internet, but rather I found it quoted on one of my regular stops which is a Christian blog that goes by the clever name of Pyromaniacs.
It has often been my thought that if one could go back to the very early Christian Church, it would be possible to see the right way to live. That those who were taught directly by the Apostles, or perhaps only a generation or two removed from them, would have had to have gotten everything right. Of course, in truth, that is to a large extent a fallacy. Even as the Apostles were still penning the letters of the New Testament, false prophets were making their way into the Church. (2 Cor. 11:13) Still, those early followers of Christ can certainly, by their example, point us toward scripture that we should remember to take heed of.
The following is a small section of the letter from Mathetes. You can find the rest of it here. I used the translation by J. B. Lightfoot.
"For Christians are not distinguished from the rest of mankind either in locality or in speech or in customs. For they dwell not somewhere in cities of their own, neither do they use some different language, nor practise an extraordinary kind of life. Nor again do they possess any invention discovered by any intelligence or study of ingenious men, nor are they masters of any human dogma as some are. But while they dwell in cities of Greeks and barbarians as the lot of each is cast, and follow the native customs in dress and food and the other arrangements of life, yet the constitution of their own citizenship, which they set forth, is marvellous,and confessedly contradicts expectation. They dwell in their own countries, but only as sojourners; they bear their share in all things as citizens, and they endure all hardships as strangers. Every foreign country is a fatherland to them, and every fatherland is foreign. They marry like all other men and they beget children; but they do not cast away their offspring. They have their meals in common, but not their wives. They find themselves in the flesh, and yet they live not after the flesh. Their existence is on earth, but their citizenship is in heaven. They obey the established laws, and they surpass the laws in their own lives. They love all men, and they are persecuted by all. They are ignored, and yet they are condemned. They are put to death, and yet they are endued with life. They are in beggary, and yet they make many rich. They are in want of all things, and yet they abound in all things. They are dishonoured, and yet they are glorified in their dishonour. They are evil spoken of, and yet they are vindicated. They are reviled, and they bless; they are insulted, and they respect. Doing good they are punished as evil-doers; being punished they rejoice, as if they were thereby quickened by life. War is waged against them as aliens by the Jews, and persecution is carried on against them by the Greeks, and yet those that hate them cannot tell the reason of their hostility."
That's right - as a Christian, our real citizenship is in heaven! And though we find ourselves in the flesh, we are not to live after the flesh! It seems that Mathetes' description of the lifestyle of the Christians of his time should make us ponder whether we fit that mold or not. And most of all, it reminds us that there is no "salvation" to be found in any government or secular leader, but that our only hope is in the Lord Jesus Christ!
I feel better now.
For those who pay attention to such things, we are in the midst of the political season, if indeed that season can be said to have a beginning or end anymore. Nevertheless, it cannot help but to wear on the mind, and as often as not, leave one in despair over the future of our nation. The rhetoric only promises to increase in volume and pitch until at least November.
That is why I found myself somewhat chastised, yet at the same time encouraged, by my discovery of a letter written somewhere between 130 and 200 A.D. by one identifying himself as Mathetes to a person named Diognetus. Of course I did not stumble on it as though it were a root across my path as I explored the jungle that is the Internet, but rather I found it quoted on one of my regular stops which is a Christian blog that goes by the clever name of Pyromaniacs.
It has often been my thought that if one could go back to the very early Christian Church, it would be possible to see the right way to live. That those who were taught directly by the Apostles, or perhaps only a generation or two removed from them, would have had to have gotten everything right. Of course, in truth, that is to a large extent a fallacy. Even as the Apostles were still penning the letters of the New Testament, false prophets were making their way into the Church. (2 Cor. 11:13) Still, those early followers of Christ can certainly, by their example, point us toward scripture that we should remember to take heed of.
The following is a small section of the letter from Mathetes. You can find the rest of it here. I used the translation by J. B. Lightfoot.
"For Christians are not distinguished from the rest of mankind either in locality or in speech or in customs. For they dwell not somewhere in cities of their own, neither do they use some different language, nor practise an extraordinary kind of life. Nor again do they possess any invention discovered by any intelligence or study of ingenious men, nor are they masters of any human dogma as some are. But while they dwell in cities of Greeks and barbarians as the lot of each is cast, and follow the native customs in dress and food and the other arrangements of life, yet the constitution of their own citizenship, which they set forth, is marvellous,and confessedly contradicts expectation. They dwell in their own countries, but only as sojourners; they bear their share in all things as citizens, and they endure all hardships as strangers. Every foreign country is a fatherland to them, and every fatherland is foreign. They marry like all other men and they beget children; but they do not cast away their offspring. They have their meals in common, but not their wives. They find themselves in the flesh, and yet they live not after the flesh. Their existence is on earth, but their citizenship is in heaven. They obey the established laws, and they surpass the laws in their own lives. They love all men, and they are persecuted by all. They are ignored, and yet they are condemned. They are put to death, and yet they are endued with life. They are in beggary, and yet they make many rich. They are in want of all things, and yet they abound in all things. They are dishonoured, and yet they are glorified in their dishonour. They are evil spoken of, and yet they are vindicated. They are reviled, and they bless; they are insulted, and they respect. Doing good they are punished as evil-doers; being punished they rejoice, as if they were thereby quickened by life. War is waged against them as aliens by the Jews, and persecution is carried on against them by the Greeks, and yet those that hate them cannot tell the reason of their hostility."
That's right - as a Christian, our real citizenship is in heaven! And though we find ourselves in the flesh, we are not to live after the flesh! It seems that Mathetes' description of the lifestyle of the Christians of his time should make us ponder whether we fit that mold or not. And most of all, it reminds us that there is no "salvation" to be found in any government or secular leader, but that our only hope is in the Lord Jesus Christ!
I feel better now.
Labels:
Christianity
Sunday, October 21, 2012
EL Bonnie on the Dyno
Last stop for EL Bonnie before hitting the "great white dyno" AKA the Salt Flats, was a mechanical dynomometer. Like much of the rest of the project, this too proved to be somewhat less straightforward than planned. Faribault Harley Davidson had come on board as a sponsor in the form of providing dyno work. Only one problem; about the time Joe and Terry were feverishly working to install the modified 61 inch motor in the EL Bonnie chassis, the FHD dyno was in the process of taking some time off (I think the term technical description was that "it blew up"). Since repairs to the Faribault dyno were not possible in time for the Knucklehead, another plan was needed.
A call from team member John Endrizzi to Pat Lehmann of Rochester Harley saved the day. Pat graciously agreed to come in on his day off to establish the baseline jetting using their SuperFlow Dyno.
The following video documents some of the dyno testing. A couple notes about the video; the first thing that you may notice is the ingenious starter system that Joe Taylor came up with. It consists of a snow blower with a go cart wheel attached in place of the rotor. Also noteworthy is that when you see Pat with the welding gloves on, it is because the plug wires kept coming loose from the magneto at RPM. Eventually he was forced to hold them in place during the dyno run. Finding this one issue alone, before making the trip all the way to the salt, was priceless.
So, what was the horsepower? I guess we just don't know. I knew going in that the dyno would probably not pick up a usable trigger from the magneto. The lack of a tachometer on the bike was also an issue. After some initial warm up runs and jet changes, Pat broke out an optical pickup which he set up to run off the engine pulley, but since he had never had occasion to use it before, there was some question as to the readings it produced. The actual readings showed over 120 horsepower at around 4800 RPM - obviously that was incorrect (at no time during the dyno session did the engine reach maximum RPMs). The RPM readings from the optical pickup seemed to be right though.
A call from team member John Endrizzi to Pat Lehmann of Rochester Harley saved the day. Pat graciously agreed to come in on his day off to establish the baseline jetting using their SuperFlow Dyno.
The following video documents some of the dyno testing. A couple notes about the video; the first thing that you may notice is the ingenious starter system that Joe Taylor came up with. It consists of a snow blower with a go cart wheel attached in place of the rotor. Also noteworthy is that when you see Pat with the welding gloves on, it is because the plug wires kept coming loose from the magneto at RPM. Eventually he was forced to hold them in place during the dyno run. Finding this one issue alone, before making the trip all the way to the salt, was priceless.
So, what was the horsepower? I guess we just don't know. I knew going in that the dyno would probably not pick up a usable trigger from the magneto. The lack of a tachometer on the bike was also an issue. After some initial warm up runs and jet changes, Pat broke out an optical pickup which he set up to run off the engine pulley, but since he had never had occasion to use it before, there was some question as to the readings it produced. The actual readings showed over 120 horsepower at around 4800 RPM - obviously that was incorrect (at no time during the dyno session did the engine reach maximum RPMs). The RPM readings from the optical pickup seemed to be right though.
After the fact I mathematically calculated the RPM from the wheel speed, confirming that the optical pickup was providing accurate data. If the horsepower readings we saw meant anything, my guess is that they were reading double the actual horsepower figure, but since the engine was only taken to about 4800 of what I hoped would be a 7500 RPM top, even that told us very little.
Oh well, perhaps the great white dyno of the Bonneville Salt Flats would provide more conclusive results...
Labels:
EL Bonnie
Tuesday, October 16, 2012
Year End Racing Update
Two local racers, who incidentally carry the Lee's Speed Shop logo on their steeds, finished the season in style.
Joe Lieske, aboard his V-Rod based gas dragster came home with the AMRA's V-Mod National Championship. Joe sealed the deal with a big win at the National Finals in Bowling Green. I am a little embarrassed to admit I have lost count of the National event wins he stacked up for the season, but I do know that Joe came home with 4 National Records along the way. In late March and early April he set the 1/8 mile ET record at 5.564 seconds, as well as both ends of the 1/4 mile record: 8.917 ET and 144.55 MPH. In late April Joe lowered the ET record to 8.875 seconds. Congratulations Joe!
On another front, Bill Hofmeister celebrated his first full year of retirement from riding flat track by, you guessed it, adding another couple wins to his long, long list. This time he rode his 900 Iron Head XR to victory at the long running Flying Dutchmen's New Ulm Short Track; not without incident however. During a heat race, problems with the rear brake forced Bill to completely remove the caliper and mount for the Open Twin Main, and since the bike sports no front brake, ...well, let's just say it is pretty plain that old age hasn't dimmed his competitive spirit much.
As for the part about Bill hanging up his racing leathers, some of us were not really surprised...
Joe Lieske, aboard his V-Rod based gas dragster came home with the AMRA's V-Mod National Championship. Joe sealed the deal with a big win at the National Finals in Bowling Green. I am a little embarrassed to admit I have lost count of the National event wins he stacked up for the season, but I do know that Joe came home with 4 National Records along the way. In late March and early April he set the 1/8 mile ET record at 5.564 seconds, as well as both ends of the 1/4 mile record: 8.917 ET and 144.55 MPH. In late April Joe lowered the ET record to 8.875 seconds. Congratulations Joe!
On another front, Bill Hofmeister celebrated his first full year of retirement from riding flat track by, you guessed it, adding another couple wins to his long, long list. This time he rode his 900 Iron Head XR to victory at the long running Flying Dutchmen's New Ulm Short Track; not without incident however. During a heat race, problems with the rear brake forced Bill to completely remove the caliper and mount for the Open Twin Main, and since the bike sports no front brake, ...well, let's just say it is pretty plain that old age hasn't dimmed his competitive spirit much.
As for the part about Bill hanging up his racing leathers, some of us were not really surprised...
Labels:
Race Results
Sunday, September 23, 2012
EL Bonnie - Flywheel Balancing Act
Yeah, OK, I know Bonneville is over, but I am going to go ahead and write this just as I would have had I not run seriously short on time leading up to it. So with that in mind, here is the next installment.
Balance the flywheels. Simple enough. In fact if you are familiar with the process you know its normally only about a two hour process. The key word here being normally. Really nothing normal about this motor though. Turning a 1939 engine of any type into a Bonneville racer is not a simple task, but add to the antiquated design, we are also dealing with a small (by Harley standards) displacement which needs to stay that way to remain in the chosen class. In this case, what I am trying to do is make up for displacement with RPMs, and RPMs call for strong and light parts.
Well, we already had some strong parts in the S and S 3-1/2 inch stroke flywheels, and while these flywheels start out considerably lighter than their OEM counterparts at 26-1/2 pounds for the pair of bare wheels, they still needed to be put on a serious diet for this special application. So... to the lathe!
I lightened the shiny new flywheels - a lot! In fact, as sometimes happens, I got a little carried away. Knowing that I was dealing with these tiny little 3-5/16" bore pistons, I "mis-underestimated" how much of the counterweight I could remove. Oops. Well, I had planned to make the pistons as light as possible anyway, so....
First thing was to track down a pair of .080" wall tool steel wrist pins. It seems that I obtained the last set on the planet from Axtell by way of Zippers. Of course they were for a Evo so I had to shorten them as well as hone the pistons for the .001" larger diameter pins. Weight savings on the pins alone was nearly 50 grams. The pistons also went on an extreme diet, with enough material removed from the insides to make any piston manufacturer cringe. I was careful to try to leave at least .180" thickness in the dome though.
I went with 55% for the flywheel balance factor, chosen because that is what the factory used for the XR750. Small motor, short stroke, and high revving - those were the characteristics I hoped EL Bonnie would share with an XR. To get there, not only did the pistons go on a diet, but even such small things as the crankpin nuts were cut down, not to mention adding an internal bevel to the ends of the pin. Before all was said and done, the finished crankshaft assembly (with rods and shafts, ready to run) weighed but 20 Lbs 5 Oz. obviously this motor borders on anorexic.
Before final assemble and true, the flywheels received the same oil shedding, heat dispersing coating as the interior of the crankcases. The underside of the pistons also received the same coating (the idea is to keep the oil moving off the inside of the piston to aid in cooling it. The domes got a ceramic coating as well as an oil retaining skirt coating.
Oil pumps on these old motors are becoming a little problematic. Back in the good old days, it seemed that a guy could always sort through a drawer full of spare oil pump gears to find pairs that would give acceptable protrusion from the body. As time goes on though, the pickings are getting pretty slim. The solution actually results in a better pump than what one might come up with if the drawer of spares was still well stocked. By surface grinding the oil pump gears so that the pairs are of matched thickness, and then surface grinding the pump body, the protrusion of the gears from the body can be "blueprinted" while compensating for the thickness of reproduction gaskets. Bear in mind that we are talking about doing this on a precision surface grinder, not a belt sander. EL Bonnie's pump was in medium poor shape, but the surface grinding treatment brought it back - that and some welding and re-machining on the cover.
That pretty well wraps up the story on the bottom end. The heads had been re-worked by Ron Adamson before the motor came to me, so I'll just comment on the rocker arms. They too received the lightening treatment; or maybe we should call it the "lightning" treatment, since we are dealing with an early Knuck. Once lightened and spec'd for shaft clearance, all that was left was to resurface the pads and treat them with the same oil shedding coating as the bottom end parts.
After all the trials and tribulations which accompanied prepping the engine parts, final assembly was somewhat anticlimactic - in other words it went smoothly. And all finished with nearly a week left for the team to install the engine in the bike and dyno it before leaving for Bonneville!
Balance the flywheels. Simple enough. In fact if you are familiar with the process you know its normally only about a two hour process. The key word here being normally. Really nothing normal about this motor though. Turning a 1939 engine of any type into a Bonneville racer is not a simple task, but add to the antiquated design, we are also dealing with a small (by Harley standards) displacement which needs to stay that way to remain in the chosen class. In this case, what I am trying to do is make up for displacement with RPMs, and RPMs call for strong and light parts.
Well, we already had some strong parts in the S and S 3-1/2 inch stroke flywheels, and while these flywheels start out considerably lighter than their OEM counterparts at 26-1/2 pounds for the pair of bare wheels, they still needed to be put on a serious diet for this special application. So... to the lathe!
I lightened the shiny new flywheels - a lot! In fact, as sometimes happens, I got a little carried away. Knowing that I was dealing with these tiny little 3-5/16" bore pistons, I "mis-underestimated" how much of the counterweight I could remove. Oops. Well, I had planned to make the pistons as light as possible anyway, so....
First thing was to track down a pair of .080" wall tool steel wrist pins. It seems that I obtained the last set on the planet from Axtell by way of Zippers. Of course they were for a Evo so I had to shorten them as well as hone the pistons for the .001" larger diameter pins. Weight savings on the pins alone was nearly 50 grams. The pistons also went on an extreme diet, with enough material removed from the insides to make any piston manufacturer cringe. I was careful to try to leave at least .180" thickness in the dome though.
I went with 55% for the flywheel balance factor, chosen because that is what the factory used for the XR750. Small motor, short stroke, and high revving - those were the characteristics I hoped EL Bonnie would share with an XR. To get there, not only did the pistons go on a diet, but even such small things as the crankpin nuts were cut down, not to mention adding an internal bevel to the ends of the pin. Before all was said and done, the finished crankshaft assembly (with rods and shafts, ready to run) weighed but 20 Lbs 5 Oz. obviously this motor borders on anorexic.
Before final assemble and true, the flywheels received the same oil shedding, heat dispersing coating as the interior of the crankcases. The underside of the pistons also received the same coating (the idea is to keep the oil moving off the inside of the piston to aid in cooling it. The domes got a ceramic coating as well as an oil retaining skirt coating.
Oil pumps on these old motors are becoming a little problematic. Back in the good old days, it seemed that a guy could always sort through a drawer full of spare oil pump gears to find pairs that would give acceptable protrusion from the body. As time goes on though, the pickings are getting pretty slim. The solution actually results in a better pump than what one might come up with if the drawer of spares was still well stocked. By surface grinding the oil pump gears so that the pairs are of matched thickness, and then surface grinding the pump body, the protrusion of the gears from the body can be "blueprinted" while compensating for the thickness of reproduction gaskets. Bear in mind that we are talking about doing this on a precision surface grinder, not a belt sander. EL Bonnie's pump was in medium poor shape, but the surface grinding treatment brought it back - that and some welding and re-machining on the cover.
That pretty well wraps up the story on the bottom end. The heads had been re-worked by Ron Adamson before the motor came to me, so I'll just comment on the rocker arms. They too received the lightening treatment; or maybe we should call it the "lightning" treatment, since we are dealing with an early Knuck. Once lightened and spec'd for shaft clearance, all that was left was to resurface the pads and treat them with the same oil shedding coating as the bottom end parts.
After all the trials and tribulations which accompanied prepping the engine parts, final assembly was somewhat anticlimactic - in other words it went smoothly. And all finished with nearly a week left for the team to install the engine in the bike and dyno it before leaving for Bonneville!
Labels:
EL Bonnie
Thursday, September 6, 2012
The Fiery Furnace
The book of Daniel was written in the 6th century B.C., that is; between 500 and 600 years before the birth of Christ. Soon after Jerusalem was conquered by Babylon and its king Nebuchadnezzar, four young men were taken from the tribe of Judah to Babylon. Here they were to be raised in the Babylonian culture so that they would be useful in dealing with the Jewish captives who were also brought there. In today's terminology we might say that they were to be brainwashed. But this brainwashing did not really seem to work as planned. While the four young men did grow up in Babylon and were promoted to positions of authority, they never forsook the God of Israel.
The four young men were named Daniel, Hananiah, Mishael, and Azariah, but they were given Babylonian names. Daniel became Belteshazzar, Hananiah became Shadrach, Mishael became Meshach, and Azariah was renamed Abednego. These last three; Shadrach, Meshach and Abednego, are the focus of our story.
Daniel chapter 3 begins with a description of a 90 foot tall golden image that king Nebuchadnezzar made. The king commanded that at the dedication of the image, when they heard the music play, everyone must fall down and worship the golden image or else be thrown into a fiery furnace. That is where we pick up the story in verse 12:
There are certain Jews whom thou hast set over the affairs of the province of Babylon, Shadrach, Meshach, and Abednego; these men, O king, have not regarded thee: they serve not thy gods, nor worship the golden image which thou hast set up. Then Nebuchadnezzar in his rage and fury commanded to bring Shadrach, Meshach, and Abednego. Then they brought these men before the king. Nebuchadnezzar spake and said unto them, Is it true, O Shadrach, Meshach, and Abednego, do not ye serve my gods, nor worship the golden image which I have set up? Now if ye be ready that at what time ye hear the sound of the cornet, flute, harp, sackbut, psaltery, and dulcimer, and all kinds of musick, ye fall down and worship the image which I have made; well: but if ye worship not, ye shall be cast the same hour into the midst of a burning fiery furnace; and who is that God that shall deliver you out of my hands? Shadrach, Meshach, and Abednego, answered and said to the king, O Nebuchadnezzar, we are not careful to answer thee in this matter. If it be so, our God whom we serve is able to deliver us from the burning fiery furnace, and he will deliver us out of thine hand, O king. But if not, be it known unto thee, O king, that we will not serve thy gods, nor worship the golden image which thou hast set up. Then was Nebuchadnezzar full of fury, and the form of his visage was changed against Shadrach, Meshach, and Abednego: therefore he spake, and commanded that they should heat the furnace one seven times more than it was wont to be heated. And he commanded the most mighty men that were in his army to bind Shadrach, Meshach, and Abednego, and to cast them into the burning fiery furnace. Then these men were bound in their coats, their hosen, and their hats, and their other garments, and were cast into the midst of the burning fiery furnace. Therefore because the king's commandment was urgent, and the furnace exceeding hot, the flames of the fire slew those men that took up Shadrach, Meshach, and Abednego. And these three men, Shadrach, Meshach, and Abednego, fell down bound into the midst of the burning fiery furnace. Then Nebuchadnezzar the king was astonied, and rose up in haste, and spake, and said unto his counsellors, Did not we cast three men bound into the midst of the fire? They answered and said unto the king, True, O king. He answered and said, Lo, I see four men loose, walking in the midst of the fire, and they have no hurt; and the form of the fourth is like the Son of God. Then Nebuchadnezzar came near to the mouth of the burning fiery furnace, and spake, and said, Shadrach, Meshach, and Abednego, ye servants of the most high God, come forth, and come hither. Then Shadrach, Meshach, and Abednego, came forth of the midst of the fire. And the princes, governors, and captains, and the king's counsellors, being gathered together, saw these men, upon whose bodies the fire had no power, nor was an hair of their head singed, neither were their coats changed, nor the smell of fire had passed on them. Then Nebuchadnezzar spake, and said, Blessed be the God of Shadrach, Meshach, and Abednego, who hath sent his angel, and delivered his servants that trusted in him, and have changed the king's word, and yielded their bodies, that they might not serve nor worship any god, except their own God.
There are a lot of thing we might learn from this story, but I'll only touch on a couple. The first thing I would like to point out is that Shadrach, Meshach and Abednego found themselves in this predicament because of their obedience to Almighty God. The 2nd Commandment, as found in Exodus 20 says: Thou shalt not make unto thee any graven image, or any likeness of any thing that is in heaven above, or that is in the earth beneath, or that is in the water under the earth. Thou shalt not bow down thyself to them, nor serve them: for I the LORD thy God am a jealous God...
In fact, these three obviously were not trouble makers; verse 12 tells us they had been put in a position of authority over the affairs of the province of Babylon. It seems that they grasped the principles laid out clearly in the New Testament, that they were to subject themselves to government ...right up until the point where government demands disobedience to God. Then, as Peter states in the book of Acts: We ought to obey God rather than men.
These three displayed their faith in the face of almost certain destruction. In verses 17&18 they say this: ...our God whom we serve is able to deliver us from the burning fiery furnace, and he will deliver us out of thine hand, O king. But if not, be it known unto thee, O king, that we will not serve thy gods, nor worship the golden image which thou hast set up.
In other words, Shadrach, Meshach and Abednego had faith that God could deliver them if he chose to, but even if God did not chose to deliver them from the furnace, they would not bow down and worship the image that Nebuchadnezzar had set up.
One other thing I would like to point out is that in verse 25, when Nebuchadnezzar notices that there were four men walking in the furnace, rather than the three they threw in, he states that the form of the fourth is like the Son of God. I would like to suggest to you that the fourth was not only like the Son of God, but that he was the Son of God.
Because Shadrach, Meshach and Abednego had faith in God they had this promise from Deuteronomy 31:6 Be strong and of a good courage, fear not, nor be afraid of them: for the LORD thy God, he it is that doth go with thee; he will not fail thee, nor forsake thee. In the New Testament this same verse is quoted in Hebrews like this: I will never leave thee, nor forsake thee.
I think it is interesting that Shadrach, Meshach and Abednego faced the penalty of being cast into a fiery furnace here on earth because they refused to sin. We face the penalty of an eternal fiery furnace because we choose to sin.
Rev. 20:11-15 And I saw a great white throne, and him that sat on it, from whose face the earth and the heaven fled away; and there was found no place for them. And I saw the dead, small and great, stand before God; and the books were opened: and another book was opened, which is the book of life: and the dead were judged out of those things which were written in the books, according to their works. And the sea gave up the dead which were in it; and death and hell delivered up the dead which were in them: and they were judged every man according to their works. And death and hell were cast into the lake of fire. This is the second death. And whosoever was not found written in the book of life was cast into the lake of fire.
These three men from our story, Shadrach, Meshach and Abednego, had the Son of God with them in the great trial of their obedience and their faith. They had a promise that he would never leave them or forsake them. But do you know what the good news is? If you are a Christian, then you have that same promise. God will never leave you or forsake you.
Just as the Son of God kept these three men from being harmed by Nebuchadnezzar's fiery furnace, he will keep you from the lake of fire. Why? Because your name is written in the book of life; that is, your name is written in the book of life if you will turn from your sins and believe on the Lord Jesus Christ, trusting that he made the payment for your sins by dying on the cross. Then you too will have God's promise of never leaving nor forsaking!
Labels:
Lessons from the Pulpit
Thursday, August 23, 2012
Vintage Nationals at Eddyville on Saturday
Just a reminder. The NVMDRA will hold a Vintage Nationals meet this weekend at Eddyville Raceway Park, Oscaloosa Iowa.
The track will open at 5:30 pm on Friday, August 24 with test and tune from 6:30 - 9:30. Race day is Saturday, with the gates opening at 10 am, time trials at 1 pm, and Eliminations starting at about 3. Eddyville Raceway Park is hosting the Vintage Nationals along side it annual "Motorcycle Mania " program, so there should be plenty of late model drag bikes to fill in any lull in the vintage races (or vice-versa). Street bike classes will also be available for both vintage and modern, so there's no excuse not to come out and join in the fun!
Vintage Top Gas and Vintage Top Fuel classes are both scheduled to run the 1/8 mile strip, which promises to really give the spectators a thrill old school style. And speaking of spectators, The Wounded Warriors Project has a rally scheduled for this event which may draw from 3000 to 5000 participants.
Meanwhile, on the home front, my friend Joe Lieske has graciously offered to transport "The Knuckledragger" to the event alongside his V-Rod based Top Gas drag bike. Joe's only problem is finding a way to slow the V-Rod down enough to run the fastest index class available for late models. I know - tough problem to have! Plans for Knuck, on the other hand are to just have some fun. I took a few moments this week to work on the carbs to hopeful make it idle better. I also worked on the trans lid which I hope will improve the shifting (or shift, singular, since it has only 2 gears). And just in case it does shift better, I also finessed the rear brake so that I will have a better chance of stopping while pavement is still available, which says way more about the weakness of 40's era brakes than the speed capability of the bike. Maybe I'll limit myself to half track passes...
Labels:
Vintage Motorcycle Drags
Subscribe to:
Posts (Atom)







