Less than forty-eight hours to go. That's right, as I sit down to write this there are less than 48 hours left until the Mayan Calender expires and the world ends. Sort of the new age version of Harold Camping's doomsday prophesy from some time back.
Now, I no more expect that the world is going to end on December 21, 2012 than I believed in Camping's nonsense (or Al Gore's nonsense for that matter) and the date may have slipped by without notice had it not been for my lovely wife. You see, my better half works in an office that attracts far more than its share of new age wackos. One of them recently asked her if she was frightened by the prospect of the upcoming world's end. Talk about a wide open witnessing opportunity! ....but my wife is an employee, so stealing her boss's time, even for a such noble purpose, is just not in the cards. But that doesn't mean I can't get in on the action, so here goes.
Are you frightened about the end of the world?
Actually not such a bad question. The Bible tells us this in the book of Hebrews: And as it is appointed unto men once to die, but after this the judgment: That ought to cause all but the most hardened to pause for thought. Suppose the world did end this Friday. What then? Well, the implication of the "world ending" is that we would all die. But the truth of the matter is this: its much more likely that YOU will die this Friday. No, I don't have some inside information about you personally, in fact chances are very good I have never met you. But look at the statistics on death. A whole lot of people die every day. Do you think you will never be one of those statistics?
While you contemplate your own mortality, though, don't forget the second part of that verse from Hebrews: but after this the judgment. So just when you have started to come to terms with the fact that you could die at any time, I go and throw the concept of judgment into the mix. Fine ...you can pretend that there is no God, and/or that there is no judgment ...that the Bible is not the Word of God, or it has mistakes, or whatever other little dodge you use to soothe your conscience ...doesn't change a thing!
The answer of course can be found in the line after the one quoted above: So Christ was once offered to bear the sins of many; and unto them that look for him shall he appear the second time without sin unto salvation.
There is only one thing that save you from things going very badly in that judgment, whether said judgment happens years from now, on Friday when the Mayan Calender expires, or later tonight. That is the blood of Jesus Christ. Unless you have already put your trust in the Lord Jesus and his sacrifice for your sins, there really needs to be a sense of urgency, end of the world or not.
Wednesday, December 19, 2012
Wednesday, December 5, 2012
Showdown at Mount Carmel
Elijah versus the 450 Prophets of Baal
The Old Testament book of Kings tells the tale of the vicious cycle of God's chosen people backsliding, and eventually repenting, only to backslide again. Through all of those cycles, more often than not, the national tone was set by the King who was in power at the time. Both Judah and Israel had kings who followed the LORD, and those who did not, at various times in their history, though it seems that Israel always had more than their share of wicked kings. When you consider the wicked kings, most would agree that Ahab was the worst of the worst. His bad reputation is perhaps only exceeded by that of his wife Jezebel.
That is the backdrop for 1 Kings 18. Ahab and his wife Jezebel reigned over the nation of Israel. They had caused the people to worship a false god named Baal, and had even broken down the alters of the one true God.
And it came to pass, when Ahab saw Elijah, that Ahab said unto him, Art thou he that troubleth Israel? And he answered, I have not troubled Israel; but thou, and thy father's house, in that ye have forsaken the commandments of the LORD, and thou hast followed Baalim.
Now therefore send, and gather to me all Israel unto mount Carmel, and the prophets of Baal four hundred and fifty, and the prophets of the groves four hundred, which eat at Jezebel's table. So Ahab sent unto all the children of Israel, and gathered the prophets together unto mount Carmel. 1 Kings 18:17-20
Here we have the Biblical version of the showdown at the OK corral, or as my title suggests, showdown at mount Carmel.
And Elijah came unto all the people, and said, How long halt ye between two opinions? if the LORD be God, follow him: but if Baal, then follow him. And the people answered him not a word. 1 Kings 18:21
Why do you suppose that the people did not answer him? The answer is right here in the verse. They didn't answer because their opinion was divided. On one hand they were the children of Israel, God's chosen people, and they remembered that. But they also had been led away into idolatry, mixing worship of the God of Abraham with worship of the gods of other nations; in this case the Phoenician deity Baal.
Then said Elijah unto the people, I, even I only, remain a prophet of the LORD; but Baal's prophets are four hundred and fifty men. Let them therefore give us two bullocks; and let them choose one bullock for themselves, and cut it in pieces, and lay it on wood, and put no fire under: and I will dress the other bullock, and lay it on wood, and put no fire under: And call ye on the name of your gods, and I will call on the name of the LORD: and the God that answereth by fire, let him be God. And all the people answered and said, It is well spoken. And Elijah said unto the prophets of Baal, Choose you one bullock for yourselves, and dress it first; for ye are many; and call on the name of your gods, but put no fire under. And they took the bullock which was given them, and they dressed it, and called on the name of Baal from morning even until noon, saying, O Baal, hear us. But there was no voice, nor any that answered. And they leaped upon the altar which was made. And it came to pass at noon, that Elijah mocked them, and said, Cry aloud: for he is a god; either he is talking, or he is pursuing, or he is in a journey, or peradventure he sleepeth, and must be awaked. 1Kings 18:22-27
Now, who says a Christian should never use sarcasm? Should never mock false gods? It seems that Elijah thought it was proper!
And they cried aloud, and cut themselves after their manner with knives and lancets, till the blood gushed out upon them. And it came to pass, when midday was past, and they prophesied until the time of the offering of the evening sacrifice, that there was neither voice, nor any to answer, nor any that regarded. And Elijah said unto all the people, Come near unto me. And all the people came near unto him. And he repaired the altar of the LORD that was broken down. And Elijah took twelve stones, according to the number of the tribes of the sons of Jacob, unto whom the word of the LORD came, saying, Israel shall be thy name: And with the stones he built an altar in the name of the LORD: and he made a trench about the altar, as great as would contain two measures of seed. And he put the wood in order, and cut the bullock in pieces, and laid him on the wood, and said, Fill four barrels with water, and pour it on the burnt sacrifice, and on the wood. 1 Kings 18:28-33
Elijah did not want there to be any doubt about what was about to happen. No one would be able explain it away as some natural phenomenon. This was to be unmistakably the hand of God at work. We just saw Elijah command them to pour 4 barrels of water onto the wood, next verse he says this:
And he said, Do it the second time. And they did it the second time. And he said, Do it the third time. And they did it the third time. And the water ran round about the altar; and he filled the trench also with water. 1 Kings 18: 34-35
At this point one might be tempted to think Elijah is just showing off, but certainly there is more to it than that. We already heard that Elijah took 12 stones to build this alter, which represented the 12 tribes of Israel, who were chosen by God to be his people. Here we see that three times, four barrels of water were poured over the sacrifice - in other words a total of 12 barrels. Now if those 12 stones represented Israel and the worship they should have given God, then I think the 12 barrels of water may just represent Israel's resistance to that worship.
And it came to pass at the time of the offering of the evening sacrifice, that Elijah the prophet came near, and said, LORD God of Abraham, Isaac, and of Israel, let it be known this day that thou art God in Israel, and that I am thy servant, and that I have done all these things at thy word. Hear me, O LORD, hear me, that this people may know that thou art the LORD God, and that thou hast turned their heart back again. Then the fire of the LORD fell, and consumed the burnt sacrifice, and the wood, and the stones, and the dust, and licked up the water that was in the trench. And when all the people saw it, they fell on their faces: and they said, The LORD, he is the God; the LORD, he is the God. 1 Kings 18: 36-39
Just a couple of observations and applications. The LORD our God is a jealous God who is worthy of worship. When we elevate some one or some thing to a place of more importance, or even equal importance to God, we are guilty of idolatry just as the nation of Israel was here in our story.
There is judgment coming. Just before Elijah called down the fire God, he prayed that Israel's heart would be turned back to the LORD. But the prophets of Baal were given no such option. You see, the people were guilty of backsliding and involved in idolatry, but they were still God's people. In the following verse, which tells of how the Prophets of Baal fared after the sacrifice was burnt, we see this:
And Elijah said unto them, Take the prophets of Baal; let not one of them escape. And they took them: and Elijah brought them down to the brook Kishon, and slew them there. 1 Kings 18: 40
The prophets of Baal were not just Israelites who had veered off course and mixed idol worship in with worship of the one true God, they completely rejected the LORD. They were enemies of God.
The big question is, which side are you on? Now, unless you are a prophet of Baal, or have otherwise set your heart solidly in opposition to God never to be changed, then it is not too late. If you will turn from your sin and trust in the Lord Jesus as your Saviour, believing that he paid for your sins on the cross and arose from the dead, then you too will become one of God's people. The miracle that the LORD will work in your heart will be just as dramatic as when Elijah called fire down from heaven!
Labels:
Christianity
Saturday, November 24, 2012
Shovelhead Hydraulics
Now, now, now ...those are not swear words, though many mechanic has used them in a tone that would imply that they are.
Introduced in 1953 to replace the ill fated Panhead "hydraulic in the top of the pushrod", certainly the 17920-53A was an big improvement since in 30+ years of wrenching I have yet to see its predecessor in working condition. I did actually meet a man once who claimed that he had a working set in his motor, but I could not verify that he was not either deaf or a liar. But I digress...
So, what is the first thing to do when you find yourself with noisy hydraulic lifters? Adjust them of course. And if that doesn't work, you adjust them again ....and yet again. After one finally realizes that further adjustment is little more than wishful thinking bordering on the vain repetition of the prayers of the heathen, then what?
Now, we have all seen Shovelhead hydraulic lifters that function flawlessly; quiet and trouble free. Common sense would tell us that for the most part this would be the norm, after all, the factory used them for over 30 years. Somehow, though, it is the ones that are noisy that stick in our memory. To be fair, a number of those that seem to be problematic are not to blame themselves, but take on the role of scape goat for other engine parts.
Low oil pressure is the first logical root cause to examine before condemning the hydraulic unit. Most who have been around Shovelheads for any time know to keep an eye on the tappet screen, since all the oil to the lifters must pass through it (hence its name). Debris plugging this small screen can definitely make for some noisy hydraulics, though the type of debris and the amount of time it took to accumulate may also indicate larger problems. Remember, the tappet screen is downstream from the gauge or sender, so you could have a good oil pressure reading, but still not enough pressure at the lifter.
The oil pump itself could also be the culprit, but there again, excess wear could itself be a symptom of worn out parts serving up a metallic oil soup. And then there are the bushings.... Oil pressure will seek the easiest path to relieve itself. Fortunately there are only a few bushings in a Shovelhead motor that are subject to pressure, those being the pinion bushing and the rocker bushings. Now lifter noise in later Shovels with the multi stage oil pumps should not be affected much by loose clearance between the pinion shaft and bushing, since the pump is designed such that it must build pressure against the top end (hydraulic lifters and rocker arms) before the pressure relief valve opens enough to supply oil to the bottom end via the pinion bushing. However, badly worn rocker bushings could still bleed off enough pressure to effectively disable the hydraulic lifters.
But what if you have good oil pressure, the rest of your engine is in good shape, and you still have noisy hydraulics? Well, maybe it's time to revisit that adjustment one last time.
First of all, I prefer to bring the engine to TDC on the compression stroke for one cylinder, and adjust both lifters for that cylinder at that point. I'll assume you can find that place in your engine's rotation. At that point the '59 to '69 FL/FLH-1200 Service Manual tells us to loosen (shorten) the pushrod until we have noticeable shake, and then extend it again until the shake is just taken up (just before it starts to compress the hydraulic unit). From that point we are to extend the pushrod 4 full turns. Fine. I have use that adjustment many, many times with good results.
Now lets look at the '70 to Early '78 FL/FLH/FX/FXE/FXS-1200 Manual. Here we find two methods. One, called the "wet" method is identical to the one we just described from the '59-'69 Manual. The other, called the "dry" method involves removing the hydraulics from the lifter, pulling the two halves apart, and cleaning out the oil (best accomplished with some spray brake parts cleaner or the equivalent). With the hydraulics cleaned of oil, we are instructed to extend the pushrod past the point where the shake is removed and all the way until the hydraulic unit is bottomed out. At this point, extending the pushrod length any further would begin to lift the valve. Here we are instructed to shorten the pushrod by exactly 1-3/4 turns. Again, I have used that adjustment many, many times with good results.
On to the '78-1/2 to '84 1200/1340cc 4 Speed Manual. Here we find the old tried and true "wet" method to be missing in action. And if that is not enough, the dry method has changed just enough to be barely noticeable (I just noticed it this summer after 30 years of valve adjustments). Now we are to follow the same procedure as the "dry" method from the '70-'78 Manual, but instead of 1-3/4 turns up from the hydraulic being bottomed out, now it calls out 1-1/2 turns. Hmm. Do I need to say it? Certainly I have used this adjustment many, many times (depending on which manual I grabbed) with good results.
But here is the interesting thing: for years I assumed that 4 turns down on a wet lifter would result in the exact same adjustment as 1-1/2 (or 1-3/4) turns up on a dry lifter. It does not! In fact, if it were not the for the 1-1/2 vs 1-3/4 discrepancy, I may have never realized this. As it turns out, it takes about 8 full turns to collapse a Shovel hydraulic from its "wet" starting point to its "dry" starting point. That means that using the "wet' adjustment method results in a hydraulic that is 4 turns up from bottomed out rather than the 1-1/2 or 1-3/4 turn up from the dry method.
[2018 Update: If the range of adjustments listed above are not enough to convince you of the relative lack of importance as to the "exact" point in the lifter's travel, I have to add one more to the list. While researching a totally unrelated issue I ran across this in Harley's "Shop Dope" publication from February 16, 1953. This gives the recommended adjustment as 5 full turns down on a wet lifter. If I count correctly, that comes to a total of four different factory settings for that lifter!]
Obviously the wet method is much less time consuming if you have no other reason to completely remove the hydraulic units from the engine, but it looks as though extending the pushrods 8-1/4 to 8-1/2 might be in order (assuming the factory had good reason to go to a tighter adjustment in later years). But it also becomes obvious that precise adjustment is not critical if all else is as it should be. So next time you adjust your lifters don't sweat it if your wrench slips and you think you may have gotten a half turn off. If its still noisy, better to spend your time investigating whether it is an engine problem or just bad lifters.
Introduced in 1953 to replace the ill fated Panhead "hydraulic in the top of the pushrod", certainly the 17920-53A was an big improvement since in 30+ years of wrenching I have yet to see its predecessor in working condition. I did actually meet a man once who claimed that he had a working set in his motor, but I could not verify that he was not either deaf or a liar. But I digress...
So, what is the first thing to do when you find yourself with noisy hydraulic lifters? Adjust them of course. And if that doesn't work, you adjust them again ....and yet again. After one finally realizes that further adjustment is little more than wishful thinking bordering on the vain repetition of the prayers of the heathen, then what?
Now, we have all seen Shovelhead hydraulic lifters that function flawlessly; quiet and trouble free. Common sense would tell us that for the most part this would be the norm, after all, the factory used them for over 30 years. Somehow, though, it is the ones that are noisy that stick in our memory. To be fair, a number of those that seem to be problematic are not to blame themselves, but take on the role of scape goat for other engine parts.
Low oil pressure is the first logical root cause to examine before condemning the hydraulic unit. Most who have been around Shovelheads for any time know to keep an eye on the tappet screen, since all the oil to the lifters must pass through it (hence its name). Debris plugging this small screen can definitely make for some noisy hydraulics, though the type of debris and the amount of time it took to accumulate may also indicate larger problems. Remember, the tappet screen is downstream from the gauge or sender, so you could have a good oil pressure reading, but still not enough pressure at the lifter.
The oil pump itself could also be the culprit, but there again, excess wear could itself be a symptom of worn out parts serving up a metallic oil soup. And then there are the bushings.... Oil pressure will seek the easiest path to relieve itself. Fortunately there are only a few bushings in a Shovelhead motor that are subject to pressure, those being the pinion bushing and the rocker bushings. Now lifter noise in later Shovels with the multi stage oil pumps should not be affected much by loose clearance between the pinion shaft and bushing, since the pump is designed such that it must build pressure against the top end (hydraulic lifters and rocker arms) before the pressure relief valve opens enough to supply oil to the bottom end via the pinion bushing. However, badly worn rocker bushings could still bleed off enough pressure to effectively disable the hydraulic lifters.
But what if you have good oil pressure, the rest of your engine is in good shape, and you still have noisy hydraulics? Well, maybe it's time to revisit that adjustment one last time.
First of all, I prefer to bring the engine to TDC on the compression stroke for one cylinder, and adjust both lifters for that cylinder at that point. I'll assume you can find that place in your engine's rotation. At that point the '59 to '69 FL/FLH-1200 Service Manual tells us to loosen (shorten) the pushrod until we have noticeable shake, and then extend it again until the shake is just taken up (just before it starts to compress the hydraulic unit). From that point we are to extend the pushrod 4 full turns. Fine. I have use that adjustment many, many times with good results.
Now lets look at the '70 to Early '78 FL/FLH/FX/FXE/FXS-1200 Manual. Here we find two methods. One, called the "wet" method is identical to the one we just described from the '59-'69 Manual. The other, called the "dry" method involves removing the hydraulics from the lifter, pulling the two halves apart, and cleaning out the oil (best accomplished with some spray brake parts cleaner or the equivalent). With the hydraulics cleaned of oil, we are instructed to extend the pushrod past the point where the shake is removed and all the way until the hydraulic unit is bottomed out. At this point, extending the pushrod length any further would begin to lift the valve. Here we are instructed to shorten the pushrod by exactly 1-3/4 turns. Again, I have used that adjustment many, many times with good results.
On to the '78-1/2 to '84 1200/1340cc 4 Speed Manual. Here we find the old tried and true "wet" method to be missing in action. And if that is not enough, the dry method has changed just enough to be barely noticeable (I just noticed it this summer after 30 years of valve adjustments). Now we are to follow the same procedure as the "dry" method from the '70-'78 Manual, but instead of 1-3/4 turns up from the hydraulic being bottomed out, now it calls out 1-1/2 turns. Hmm. Do I need to say it? Certainly I have used this adjustment many, many times (depending on which manual I grabbed) with good results.
But here is the interesting thing: for years I assumed that 4 turns down on a wet lifter would result in the exact same adjustment as 1-1/2 (or 1-3/4) turns up on a dry lifter. It does not! In fact, if it were not the for the 1-1/2 vs 1-3/4 discrepancy, I may have never realized this. As it turns out, it takes about 8 full turns to collapse a Shovel hydraulic from its "wet" starting point to its "dry" starting point. That means that using the "wet' adjustment method results in a hydraulic that is 4 turns up from bottomed out rather than the 1-1/2 or 1-3/4 turn up from the dry method.
[2018 Update: If the range of adjustments listed above are not enough to convince you of the relative lack of importance as to the "exact" point in the lifter's travel, I have to add one more to the list. While researching a totally unrelated issue I ran across this in Harley's "Shop Dope" publication from February 16, 1953. This gives the recommended adjustment as 5 full turns down on a wet lifter. If I count correctly, that comes to a total of four different factory settings for that lifter!]
Obviously the wet method is much less time consuming if you have no other reason to completely remove the hydraulic units from the engine, but it looks as though extending the pushrods 8-1/4 to 8-1/2 might be in order (assuming the factory had good reason to go to a tighter adjustment in later years). But it also becomes obvious that precise adjustment is not critical if all else is as it should be. So next time you adjust your lifters don't sweat it if your wrench slips and you think you may have gotten a half turn off. If its still noisy, better to spend your time investigating whether it is an engine problem or just bad lifters.
Labels:
Shovelhead Tech
Monday, November 5, 2012
Old Letters - Second Time Around
Generally speaking, I do not recycle my previous blog posts, but with the election tomorrow (finally!) I thought this a good time to make an exception. Since this was originally posted in January of this year, one can appreciate how much the fever pitch of the rhetoric has accelerated in the interval. Whether the turmoil dies down after the election or not remains to be seen, however, by way of a second century letter, I would like to share a comforting thought or two. So, without further fanfare:
For those who pay attention to such things, we are in the midst of the political season, if indeed that season can be said to have a beginning or end anymore. Nevertheless, it cannot help but to wear on the mind, and as often as not, leave one in despair over the future of our nation. The rhetoric only promises to increase in volume and pitch until at least November.
That is why I found myself somewhat chastised, yet at the same time encouraged, by my discovery of a letter written somewhere between 130 and 200 A.D. by one identifying himself as Mathetes to a person named Diognetus. Of course I did not stumble on it as though it were a root across my path as I explored the jungle that is the Internet, but rather I found it quoted on one of my regular stops which is a Christian blog that goes by the clever name of Pyromaniacs.
It has often been my thought that if one could go back to the very early Christian Church, it would be possible to see the right way to live. That those who were taught directly by the Apostles, or perhaps only a generation or two removed from them, would have had to have gotten everything right. Of course, in truth, that is to a large extent a fallacy. Even as the Apostles were still penning the letters of the New Testament, false prophets were making their way into the Church. (2 Cor. 11:13) Still, those early followers of Christ can certainly, by their example, point us toward scripture that we should remember to take heed of.
The following is a small section of the letter from Mathetes. You can find the rest of it here. I used the translation by J. B. Lightfoot.
"For Christians are not distinguished from the rest of mankind either in locality or in speech or in customs. For they dwell not somewhere in cities of their own, neither do they use some different language, nor practise an extraordinary kind of life. Nor again do they possess any invention discovered by any intelligence or study of ingenious men, nor are they masters of any human dogma as some are. But while they dwell in cities of Greeks and barbarians as the lot of each is cast, and follow the native customs in dress and food and the other arrangements of life, yet the constitution of their own citizenship, which they set forth, is marvellous,and confessedly contradicts expectation. They dwell in their own countries, but only as sojourners; they bear their share in all things as citizens, and they endure all hardships as strangers. Every foreign country is a fatherland to them, and every fatherland is foreign. They marry like all other men and they beget children; but they do not cast away their offspring. They have their meals in common, but not their wives. They find themselves in the flesh, and yet they live not after the flesh. Their existence is on earth, but their citizenship is in heaven. They obey the established laws, and they surpass the laws in their own lives. They love all men, and they are persecuted by all. They are ignored, and yet they are condemned. They are put to death, and yet they are endued with life. They are in beggary, and yet they make many rich. They are in want of all things, and yet they abound in all things. They are dishonoured, and yet they are glorified in their dishonour. They are evil spoken of, and yet they are vindicated. They are reviled, and they bless; they are insulted, and they respect. Doing good they are punished as evil-doers; being punished they rejoice, as if they were thereby quickened by life. War is waged against them as aliens by the Jews, and persecution is carried on against them by the Greeks, and yet those that hate them cannot tell the reason of their hostility."
That's right - as a Christian, our real citizenship is in heaven! And though we find ourselves in the flesh, we are not to live after the flesh! It seems that Mathetes' description of the lifestyle of the Christians of his time should make us ponder whether we fit that mold or not. And most of all, it reminds us that there is no "salvation" to be found in any government or secular leader, but that our only hope is in the Lord Jesus Christ!
I feel better now.
For those who pay attention to such things, we are in the midst of the political season, if indeed that season can be said to have a beginning or end anymore. Nevertheless, it cannot help but to wear on the mind, and as often as not, leave one in despair over the future of our nation. The rhetoric only promises to increase in volume and pitch until at least November.
That is why I found myself somewhat chastised, yet at the same time encouraged, by my discovery of a letter written somewhere between 130 and 200 A.D. by one identifying himself as Mathetes to a person named Diognetus. Of course I did not stumble on it as though it were a root across my path as I explored the jungle that is the Internet, but rather I found it quoted on one of my regular stops which is a Christian blog that goes by the clever name of Pyromaniacs.
It has often been my thought that if one could go back to the very early Christian Church, it would be possible to see the right way to live. That those who were taught directly by the Apostles, or perhaps only a generation or two removed from them, would have had to have gotten everything right. Of course, in truth, that is to a large extent a fallacy. Even as the Apostles were still penning the letters of the New Testament, false prophets were making their way into the Church. (2 Cor. 11:13) Still, those early followers of Christ can certainly, by their example, point us toward scripture that we should remember to take heed of.
The following is a small section of the letter from Mathetes. You can find the rest of it here. I used the translation by J. B. Lightfoot.
"For Christians are not distinguished from the rest of mankind either in locality or in speech or in customs. For they dwell not somewhere in cities of their own, neither do they use some different language, nor practise an extraordinary kind of life. Nor again do they possess any invention discovered by any intelligence or study of ingenious men, nor are they masters of any human dogma as some are. But while they dwell in cities of Greeks and barbarians as the lot of each is cast, and follow the native customs in dress and food and the other arrangements of life, yet the constitution of their own citizenship, which they set forth, is marvellous,and confessedly contradicts expectation. They dwell in their own countries, but only as sojourners; they bear their share in all things as citizens, and they endure all hardships as strangers. Every foreign country is a fatherland to them, and every fatherland is foreign. They marry like all other men and they beget children; but they do not cast away their offspring. They have their meals in common, but not their wives. They find themselves in the flesh, and yet they live not after the flesh. Their existence is on earth, but their citizenship is in heaven. They obey the established laws, and they surpass the laws in their own lives. They love all men, and they are persecuted by all. They are ignored, and yet they are condemned. They are put to death, and yet they are endued with life. They are in beggary, and yet they make many rich. They are in want of all things, and yet they abound in all things. They are dishonoured, and yet they are glorified in their dishonour. They are evil spoken of, and yet they are vindicated. They are reviled, and they bless; they are insulted, and they respect. Doing good they are punished as evil-doers; being punished they rejoice, as if they were thereby quickened by life. War is waged against them as aliens by the Jews, and persecution is carried on against them by the Greeks, and yet those that hate them cannot tell the reason of their hostility."
That's right - as a Christian, our real citizenship is in heaven! And though we find ourselves in the flesh, we are not to live after the flesh! It seems that Mathetes' description of the lifestyle of the Christians of his time should make us ponder whether we fit that mold or not. And most of all, it reminds us that there is no "salvation" to be found in any government or secular leader, but that our only hope is in the Lord Jesus Christ!
I feel better now.
Labels:
Christianity
Sunday, October 21, 2012
EL Bonnie on the Dyno
Last stop for EL Bonnie before hitting the "great white dyno" AKA the Salt Flats, was a mechanical dynomometer. Like much of the rest of the project, this too proved to be somewhat less straightforward than planned. Faribault Harley Davidson had come on board as a sponsor in the form of providing dyno work. Only one problem; about the time Joe and Terry were feverishly working to install the modified 61 inch motor in the EL Bonnie chassis, the FHD dyno was in the process of taking some time off (I think the term technical description was that "it blew up"). Since repairs to the Faribault dyno were not possible in time for the Knucklehead, another plan was needed.
A call from team member John Endrizzi to Pat Lehmann of Rochester Harley saved the day. Pat graciously agreed to come in on his day off to establish the baseline jetting using their SuperFlow Dyno.
The following video documents some of the dyno testing. A couple notes about the video; the first thing that you may notice is the ingenious starter system that Joe Taylor came up with. It consists of a snow blower with a go cart wheel attached in place of the rotor. Also noteworthy is that when you see Pat with the welding gloves on, it is because the plug wires kept coming loose from the magneto at RPM. Eventually he was forced to hold them in place during the dyno run. Finding this one issue alone, before making the trip all the way to the salt, was priceless.
So, what was the horsepower? I guess we just don't know. I knew going in that the dyno would probably not pick up a usable trigger from the magneto. The lack of a tachometer on the bike was also an issue. After some initial warm up runs and jet changes, Pat broke out an optical pickup which he set up to run off the engine pulley, but since he had never had occasion to use it before, there was some question as to the readings it produced. The actual readings showed over 120 horsepower at around 4800 RPM - obviously that was incorrect (at no time during the dyno session did the engine reach maximum RPMs). The RPM readings from the optical pickup seemed to be right though.
A call from team member John Endrizzi to Pat Lehmann of Rochester Harley saved the day. Pat graciously agreed to come in on his day off to establish the baseline jetting using their SuperFlow Dyno.
The following video documents some of the dyno testing. A couple notes about the video; the first thing that you may notice is the ingenious starter system that Joe Taylor came up with. It consists of a snow blower with a go cart wheel attached in place of the rotor. Also noteworthy is that when you see Pat with the welding gloves on, it is because the plug wires kept coming loose from the magneto at RPM. Eventually he was forced to hold them in place during the dyno run. Finding this one issue alone, before making the trip all the way to the salt, was priceless.
So, what was the horsepower? I guess we just don't know. I knew going in that the dyno would probably not pick up a usable trigger from the magneto. The lack of a tachometer on the bike was also an issue. After some initial warm up runs and jet changes, Pat broke out an optical pickup which he set up to run off the engine pulley, but since he had never had occasion to use it before, there was some question as to the readings it produced. The actual readings showed over 120 horsepower at around 4800 RPM - obviously that was incorrect (at no time during the dyno session did the engine reach maximum RPMs). The RPM readings from the optical pickup seemed to be right though.
After the fact I mathematically calculated the RPM from the wheel speed, confirming that the optical pickup was providing accurate data. If the horsepower readings we saw meant anything, my guess is that they were reading double the actual horsepower figure, but since the engine was only taken to about 4800 of what I hoped would be a 7500 RPM top, even that told us very little.
Oh well, perhaps the great white dyno of the Bonneville Salt Flats would provide more conclusive results...
Labels:
EL Bonnie
Tuesday, October 16, 2012
Year End Racing Update
Two local racers, who incidentally carry the Lee's Speed Shop logo on their steeds, finished the season in style.
Joe Lieske, aboard his V-Rod based gas dragster came home with the AMRA's V-Mod National Championship. Joe sealed the deal with a big win at the National Finals in Bowling Green. I am a little embarrassed to admit I have lost count of the National event wins he stacked up for the season, but I do know that Joe came home with 4 National Records along the way. In late March and early April he set the 1/8 mile ET record at 5.564 seconds, as well as both ends of the 1/4 mile record: 8.917 ET and 144.55 MPH. In late April Joe lowered the ET record to 8.875 seconds. Congratulations Joe!
On another front, Bill Hofmeister celebrated his first full year of retirement from riding flat track by, you guessed it, adding another couple wins to his long, long list. This time he rode his 900 Iron Head XR to victory at the long running Flying Dutchmen's New Ulm Short Track; not without incident however. During a heat race, problems with the rear brake forced Bill to completely remove the caliper and mount for the Open Twin Main, and since the bike sports no front brake, ...well, let's just say it is pretty plain that old age hasn't dimmed his competitive spirit much.
As for the part about Bill hanging up his racing leathers, some of us were not really surprised...
Joe Lieske, aboard his V-Rod based gas dragster came home with the AMRA's V-Mod National Championship. Joe sealed the deal with a big win at the National Finals in Bowling Green. I am a little embarrassed to admit I have lost count of the National event wins he stacked up for the season, but I do know that Joe came home with 4 National Records along the way. In late March and early April he set the 1/8 mile ET record at 5.564 seconds, as well as both ends of the 1/4 mile record: 8.917 ET and 144.55 MPH. In late April Joe lowered the ET record to 8.875 seconds. Congratulations Joe!
On another front, Bill Hofmeister celebrated his first full year of retirement from riding flat track by, you guessed it, adding another couple wins to his long, long list. This time he rode his 900 Iron Head XR to victory at the long running Flying Dutchmen's New Ulm Short Track; not without incident however. During a heat race, problems with the rear brake forced Bill to completely remove the caliper and mount for the Open Twin Main, and since the bike sports no front brake, ...well, let's just say it is pretty plain that old age hasn't dimmed his competitive spirit much.
As for the part about Bill hanging up his racing leathers, some of us were not really surprised...
Labels:
Race Results
Sunday, September 23, 2012
EL Bonnie - Flywheel Balancing Act
Yeah, OK, I know Bonneville is over, but I am going to go ahead and write this just as I would have had I not run seriously short on time leading up to it. So with that in mind, here is the next installment.
Balance the flywheels. Simple enough. In fact if you are familiar with the process you know its normally only about a two hour process. The key word here being normally. Really nothing normal about this motor though. Turning a 1939 engine of any type into a Bonneville racer is not a simple task, but add to the antiquated design, we are also dealing with a small (by Harley standards) displacement which needs to stay that way to remain in the chosen class. In this case, what I am trying to do is make up for displacement with RPMs, and RPMs call for strong and light parts.
Well, we already had some strong parts in the S and S 3-1/2 inch stroke flywheels, and while these flywheels start out considerably lighter than their OEM counterparts at 26-1/2 pounds for the pair of bare wheels, they still needed to be put on a serious diet for this special application. So... to the lathe!
I lightened the shiny new flywheels - a lot! In fact, as sometimes happens, I got a little carried away. Knowing that I was dealing with these tiny little 3-5/16" bore pistons, I "mis-underestimated" how much of the counterweight I could remove. Oops. Well, I had planned to make the pistons as light as possible anyway, so....
First thing was to track down a pair of .080" wall tool steel wrist pins. It seems that I obtained the last set on the planet from Axtell by way of Zippers. Of course they were for a Evo so I had to shorten them as well as hone the pistons for the .001" larger diameter pins. Weight savings on the pins alone was nearly 50 grams. The pistons also went on an extreme diet, with enough material removed from the insides to make any piston manufacturer cringe. I was careful to try to leave at least .180" thickness in the dome though.
I went with 55% for the flywheel balance factor, chosen because that is what the factory used for the XR750. Small motor, short stroke, and high revving - those were the characteristics I hoped EL Bonnie would share with an XR. To get there, not only did the pistons go on a diet, but even such small things as the crankpin nuts were cut down, not to mention adding an internal bevel to the ends of the pin. Before all was said and done, the finished crankshaft assembly (with rods and shafts, ready to run) weighed but 20 Lbs 5 Oz. obviously this motor borders on anorexic.
Before final assemble and true, the flywheels received the same oil shedding, heat dispersing coating as the interior of the crankcases. The underside of the pistons also received the same coating (the idea is to keep the oil moving off the inside of the piston to aid in cooling it. The domes got a ceramic coating as well as an oil retaining skirt coating.
Oil pumps on these old motors are becoming a little problematic. Back in the good old days, it seemed that a guy could always sort through a drawer full of spare oil pump gears to find pairs that would give acceptable protrusion from the body. As time goes on though, the pickings are getting pretty slim. The solution actually results in a better pump than what one might come up with if the drawer of spares was still well stocked. By surface grinding the oil pump gears so that the pairs are of matched thickness, and then surface grinding the pump body, the protrusion of the gears from the body can be "blueprinted" while compensating for the thickness of reproduction gaskets. Bear in mind that we are talking about doing this on a precision surface grinder, not a belt sander. EL Bonnie's pump was in medium poor shape, but the surface grinding treatment brought it back - that and some welding and re-machining on the cover.
That pretty well wraps up the story on the bottom end. The heads had been re-worked by Ron Adamson before the motor came to me, so I'll just comment on the rocker arms. They too received the lightening treatment; or maybe we should call it the "lightning" treatment, since we are dealing with an early Knuck. Once lightened and spec'd for shaft clearance, all that was left was to resurface the pads and treat them with the same oil shedding coating as the bottom end parts.
After all the trials and tribulations which accompanied prepping the engine parts, final assembly was somewhat anticlimactic - in other words it went smoothly. And all finished with nearly a week left for the team to install the engine in the bike and dyno it before leaving for Bonneville!
Balance the flywheels. Simple enough. In fact if you are familiar with the process you know its normally only about a two hour process. The key word here being normally. Really nothing normal about this motor though. Turning a 1939 engine of any type into a Bonneville racer is not a simple task, but add to the antiquated design, we are also dealing with a small (by Harley standards) displacement which needs to stay that way to remain in the chosen class. In this case, what I am trying to do is make up for displacement with RPMs, and RPMs call for strong and light parts.
Well, we already had some strong parts in the S and S 3-1/2 inch stroke flywheels, and while these flywheels start out considerably lighter than their OEM counterparts at 26-1/2 pounds for the pair of bare wheels, they still needed to be put on a serious diet for this special application. So... to the lathe!
I lightened the shiny new flywheels - a lot! In fact, as sometimes happens, I got a little carried away. Knowing that I was dealing with these tiny little 3-5/16" bore pistons, I "mis-underestimated" how much of the counterweight I could remove. Oops. Well, I had planned to make the pistons as light as possible anyway, so....
First thing was to track down a pair of .080" wall tool steel wrist pins. It seems that I obtained the last set on the planet from Axtell by way of Zippers. Of course they were for a Evo so I had to shorten them as well as hone the pistons for the .001" larger diameter pins. Weight savings on the pins alone was nearly 50 grams. The pistons also went on an extreme diet, with enough material removed from the insides to make any piston manufacturer cringe. I was careful to try to leave at least .180" thickness in the dome though.
I went with 55% for the flywheel balance factor, chosen because that is what the factory used for the XR750. Small motor, short stroke, and high revving - those were the characteristics I hoped EL Bonnie would share with an XR. To get there, not only did the pistons go on a diet, but even such small things as the crankpin nuts were cut down, not to mention adding an internal bevel to the ends of the pin. Before all was said and done, the finished crankshaft assembly (with rods and shafts, ready to run) weighed but 20 Lbs 5 Oz. obviously this motor borders on anorexic.
Before final assemble and true, the flywheels received the same oil shedding, heat dispersing coating as the interior of the crankcases. The underside of the pistons also received the same coating (the idea is to keep the oil moving off the inside of the piston to aid in cooling it. The domes got a ceramic coating as well as an oil retaining skirt coating.
Oil pumps on these old motors are becoming a little problematic. Back in the good old days, it seemed that a guy could always sort through a drawer full of spare oil pump gears to find pairs that would give acceptable protrusion from the body. As time goes on though, the pickings are getting pretty slim. The solution actually results in a better pump than what one might come up with if the drawer of spares was still well stocked. By surface grinding the oil pump gears so that the pairs are of matched thickness, and then surface grinding the pump body, the protrusion of the gears from the body can be "blueprinted" while compensating for the thickness of reproduction gaskets. Bear in mind that we are talking about doing this on a precision surface grinder, not a belt sander. EL Bonnie's pump was in medium poor shape, but the surface grinding treatment brought it back - that and some welding and re-machining on the cover.
That pretty well wraps up the story on the bottom end. The heads had been re-worked by Ron Adamson before the motor came to me, so I'll just comment on the rocker arms. They too received the lightening treatment; or maybe we should call it the "lightning" treatment, since we are dealing with an early Knuck. Once lightened and spec'd for shaft clearance, all that was left was to resurface the pads and treat them with the same oil shedding coating as the bottom end parts.
After all the trials and tribulations which accompanied prepping the engine parts, final assembly was somewhat anticlimactic - in other words it went smoothly. And all finished with nearly a week left for the team to install the engine in the bike and dyno it before leaving for Bonneville!
Labels:
EL Bonnie
Subscribe to:
Posts (Atom)






