Thursday, September 6, 2012

The Fiery Furnace


The book of Daniel was written in the 6th century B.C., that is; between 500 and 600 years before the birth of Christ. Soon after Jerusalem was conquered by Babylon and its king Nebuchadnezzar, four young men were taken from the tribe of Judah to Babylon. Here they were to be raised in the Babylonian culture so that they would be useful in dealing with the Jewish captives who were also brought there. In today's terminology we might say that they were to be brainwashed. But this brainwashing did not really seem to work as planned. While the four young men did grow up in Babylon and were promoted to positions of authority, they never forsook the God of Israel.

The four young men were named Daniel, Hananiah, Mishael, and Azariah, but they were given Babylonian names. Daniel became Belteshazzar, Hananiah became Shadrach, Mishael became Meshach, and Azariah was renamed Abednego. These last three; Shadrach, Meshach and Abednego, are the focus of our story.

Daniel chapter 3 begins with a description of a 90 foot tall golden image that king Nebuchadnezzar made. The king commanded that at the dedication of the image, when they heard the music play, everyone must fall down and worship the golden image or else be thrown into a fiery furnace. That is where we pick up the story in verse 12:

 There are certain Jews whom thou hast set over the affairs of the province of Babylon, Shadrach, Meshach, and Abednego; these men, O king, have not regarded thee: they serve not thy gods, nor worship the golden image which thou hast set up. Then Nebuchadnezzar in his rage and fury commanded to bring Shadrach, Meshach, and Abednego. Then they brought these men before the king. Nebuchadnezzar spake and said unto them, Is it true, O Shadrach, Meshach, and Abednego, do not ye serve my gods, nor worship the golden image which I have set up? Now if ye be ready that at what time ye hear the sound of the cornet, flute, harp, sackbut, psaltery, and dulcimer, and all kinds of musick, ye fall down and worship the image which I have made; well: but if ye worship not, ye shall be cast the same hour into the midst of a burning fiery furnace; and who is that God that shall deliver you out of my hands? Shadrach, Meshach, and Abednego, answered and said to the king, O Nebuchadnezzar, we are not careful to answer thee in this matter. If it be so, our God whom we serve is able to deliver us from the burning fiery furnace, and he will deliver us out of thine hand, O king. But if not, be it known unto thee, O king, that we will not serve thy gods, nor worship the golden image which thou hast set up. Then was Nebuchadnezzar full of fury, and the form of his visage was changed against Shadrach, Meshach, and Abednego: therefore he spake, and commanded that they should heat the furnace one seven times more than it was wont to be heated. And he commanded the most mighty men that were in his army to bind Shadrach, Meshach, and Abednego, and to cast them into the burning fiery furnace. Then these men were bound in their coats, their hosen, and their hats, and their other garments, and were cast into the midst of the burning fiery furnace. Therefore because the king's commandment was urgent, and the furnace exceeding hot, the flames of the fire slew those men that took up Shadrach, Meshach, and Abednego. And these three men, Shadrach, Meshach, and Abednego, fell down bound into the midst of the burning fiery furnace. Then Nebuchadnezzar the king was astonied, and rose up in haste, and spake, and said unto his counsellors, Did not we cast three men bound into the midst of the fire? They answered and said unto the king, True, O king. He answered and said, Lo, I see four men loose, walking in the midst of the fire, and they have no hurt; and the form of the fourth is like the Son of God.  Then Nebuchadnezzar came near to the mouth of the burning fiery furnace, and spake, and said, Shadrach, Meshach, and Abednego, ye servants of the most high God, come forth, and come hither. Then Shadrach, Meshach, and Abednego, came forth of the midst of the fire. And the princes, governors, and captains, and the king's counsellors, being gathered together, saw these men, upon whose bodies the fire had no power, nor was an hair of their head singed, neither were their coats changed, nor the smell of fire had passed on them. Then Nebuchadnezzar spake, and said, Blessed be the God of Shadrach, Meshach, and Abednego, who hath sent his angel, and delivered his servants that trusted in him, and have changed the king's word, and yielded their bodies, that they might not serve nor worship any god, except their own God.

There are a lot of thing we might learn from this story, but I'll only touch on a couple. The first thing I would like to point out is that Shadrach, Meshach and Abednego found themselves in this predicament because of their obedience to Almighty God. The 2nd Commandment, as found in Exodus 20 says: Thou shalt not make unto thee any graven image, or any likeness of any thing that is in heaven above, or that is in the earth beneath, or that is in the water under the earth. Thou shalt not bow down thyself to them, nor serve them: for I the LORD thy God am a jealous God...

In fact, these three obviously were not trouble makers; verse 12 tells us they had been put in a position of authority over the affairs of the province of Babylon. It seems that they grasped the principles laid out clearly in the New Testament, that they were to subject themselves to government ...right up until the point where government demands disobedience to God. Then, as Peter states in the book of Acts:  We ought to obey God rather than men.

These three displayed their faith in the face of almost certain destruction. In verses 17&18 they say this: ...our God whom we serve is able to deliver us from the burning fiery furnace, and he will deliver us out of thine hand, O king. But if not, be it known unto thee, O king, that we will not serve thy gods, nor worship the golden image which thou hast set up.

In other words, Shadrach, Meshach and Abednego had faith that God could deliver them if he chose to, but even if God did not chose to deliver them from the furnace, they would not bow down and worship the image that Nebuchadnezzar had set up.

One other thing I would like to point out is that in verse 25, when Nebuchadnezzar notices that there were four men walking in the furnace, rather than the three they threw in, he states that the form of the fourth is like the Son of God. I would like to suggest to you that the fourth was not only like the Son of God, but that he was the Son of God.

Because Shadrach, Meshach and Abednego had faith in God they had this promise from Deuteronomy 31:6 Be strong and of a good courage, fear not, nor be afraid of them: for the LORD thy God, he it is that doth go with thee; he will not fail thee, nor forsake thee.  In the New Testament this same verse is quoted in Hebrews like this: I will never leave thee, nor forsake thee.

I think it is interesting that Shadrach, Meshach and Abednego faced the penalty of being cast into a fiery furnace here on earth because they refused to sin. We face the penalty of an eternal fiery furnace because we choose to sin.

Rev. 20:11-15 And I saw a great white throne, and him that sat on it, from whose face the earth and the heaven fled away; and there was found no place for them.  And I saw the dead, small and great, stand before God; and the books were opened: and another book was opened, which is the book of life: and the dead were judged out of those things which were written in the books, according to their works.  And the sea gave up the dead which were in it; and death and hell delivered up the dead which were in them: and they were judged every man according to their works.  And death and hell were cast into the lake of fire. This is the second death.  And whosoever was not found written in the book of life was cast into the lake of fire.

These three men from our story, Shadrach, Meshach and Abednego, had the Son of God with them in the great trial of their obedience and their faith. They had a promise that he would never leave them or forsake them.  But do you know what the good news is? If you are a Christian, then you have that same promise. God will never leave you or forsake you.

Just as the Son of God kept these three men from being harmed by Nebuchadnezzar's fiery furnace, he will keep you from the lake of fire. Why? Because your name is written in the book of life; that is, your name is written in the book of life if you will turn from your sins and believe on the Lord Jesus Christ, trusting that he made the payment for your sins by dying on the cross. Then you too will have God's promise of never leaving nor forsaking!

Thursday, August 23, 2012

Vintage Nationals at Eddyville on Saturday

Just a reminder.  The NVMDRA will hold a Vintage Nationals meet this weekend at Eddyville Raceway Park, Oscaloosa Iowa. 



The track will open at 5:30 pm on Friday, August 24 with test and tune from 6:30 - 9:30.  Race day is Saturday, with the gates opening at 10 am, time trials at 1 pm, and Eliminations starting at about 3.  Eddyville Raceway Park is hosting the Vintage Nationals along side it annual "Motorcycle Mania " program, so there should be plenty of late model drag bikes to fill in any lull in the vintage races (or vice-versa).  Street bike classes will also be available for both vintage and modern, so there's no excuse not to come out and join in the fun!

Vintage Top Gas and Vintage Top Fuel classes are both scheduled to run the 1/8 mile strip, which promises to really give the spectators a thrill old school style.  And speaking of spectators, The Wounded Warriors Project has a rally scheduled  for this event which may draw from 3000 to 5000 participants.

Meanwhile, on the home front, my friend Joe Lieske has graciously offered to transport "The Knuckledragger" to the event alongside his V-Rod based Top Gas drag bike.  Joe's only problem is finding a way to slow the V-Rod down enough to run the fastest index class available for late models.  I know - tough problem to have!  Plans for Knuck, on the other hand are to just have some fun.  I took a few moments this week to work on the carbs to hopeful make it idle better.  I also worked on the trans lid which I hope will improve the shifting (or shift, singular, since it has only 2 gears).  And just in case it does shift better, I also finessed the rear brake so that I will have a better chance of stopping while pavement is still available, which says way more about the weakness of 40's era brakes than the speed capability of the bike.  Maybe I'll limit myself to half track passes...

Wednesday, August 15, 2012

EL Bonnie Part 3: Don't Try This at Home

As I left off with the 61 cubic inch EL Bonnie motor, after a detour to make the cam cover usable, I was finally ready to blueprint the breather timing.  Mocking up the lower end reminded me that I would have to cut the flywheel diameter down to clear the crankcase oil scraper (pre 1940 flywheels were slightly smaller diameter than those used since). Some judicious work on the lathe brought the scraper to flywheel clearance to a snug .006".

With the mocked up crank assembly in the cases, next up was to get the degree wheel mounted and accurately indicating TDC.  If you have never done this, there is slightly more to it than just bringing the piston to the top of the cylinder and lining up the TDC mark of the degree wheel to a pointer.  That gets you in the ballpark, but certainly not close enough to base any timing events from.  Since there was no head installed, here is an easy way to get the degree wheel "degreed in:
  1. With the piston at the top, mount a dial indicator and zero the needle
  2. Install the degree wheel on the sprocket shaft and align a pointer with the TDC mark
  3. Pick an arbitrary number on the dial indicator (example - .050) 
  4. Rotate the crank counterclockwise until the needle on the dial indicator matches the number you have chosen.  Note the exact reading on the degree wheel at that point (example - 9-1/2 degrees after TDC)
  5. Rotate the crank the opposite direction, past TDC until you reach the same dial indicator reading you chose in step 3 above, and again note the reading on the degree wheel
  6. If the two reading from steps 4 & 5 match exactly (unlikely), you are done.  If they don't match, then loosen the degree wheel and move it to split the difference.  For example if your reading from step 4 was 9-1/2 degrees after TDC and the reading from step 5 was 10-1/2 degrees before TDC, then move the degree wheel so that its pointer is on 10 degrees. 
  7. Repeat steps 4 & 5 until both give exactly the same number of degrees before and after TDC
(note:  Blogger, in their infinite wisdom, autmatically converted the numbered bullet points I have in the draft form to the goofy looking flowers that you see - guess you will just have to count them)




Once the degree wheel was properly installed, the opening and closing specs for the breather gear was checked, looking through the lifter block holes.  Rather than go through the process here, I suggest you download the excellent instructions available from S & S Cycle here.

Since a degree wheel was installed, it only made sense to check out the cams, especially given the discrepancy found in cam opening and closing specs due to mis-machined lifter blocks.  The lifter blocks seemed to be OK, but the exercise did pretty well make the cam choice for me.  The KN420 cam from S & S checked out good.  The old Sifton, not so much.  One intake lobe showed a 12 degree discrepancy on the opening, 5 degrees on the closing (for a total of 17 degrees less duration) and .020" less lift than it should have, all despite showing no sign that it had ever been run.

Of course since the motor was mocked up as far as it was, it also made sense to clay the pistons to get a sense of how much valve to piston clearance there was.  The answer to that question was a lot.  In fact, more than a lot; make it a huge amount.  That was a bit worrisome, given the fact that I was already apprehensive about the compression ratio the engine would wind up with.  The custom built pistons claimed a 10:1 compression ratio but the large diameter intake valves were sure to need a little more radial clearance in the valve pockets.  Given my "druthers" I'd have liked to see 12:1 for a starting point.

Time to check the piston dome volume, another fairly straight forward procedure which involves putting some grease on  the rings, installing the piston into the cylinder to a measured depth, capping the cylinder with a Plexiglas plate and a burret to measure the amount of oil it takes to fill the void.  Then by mathematically calculating the number of cc's that would be in the cylinder without the piston dome (using piston depth and bore) and subtracting the measured cc's with the piston dome in the cylinder, the actual dome volume is revealed.



Entering all the figures into my Engine Analyzer program, which takes into account head volume, piston deck height, head gasket thickness, head gasket bore and adjusting for fire ring and fire ring volume, I came up with a very disappointing 8.25:1 compression ratio.  Worse yet, there was no room to shave the heads due to the proximity of the 2.060" intake valve to the fire ring.  Now what?  I was really beginning to worry that this little 61" motor would be badly over-cammed at this compression ratio. 

I decided to call Jim Leineweber of the cam company that bears his name.  While he was not wild about the low compression ratio, he said he currently had nothing on the shelf that would work any better.  Jim did boost my confidence by affirming the clearances that I planned for the various engine parts, but then I always have been one of those who do well on tests.  And it really did seem much like an exam, as he asked what each clearance I planned to use, and then gave each of my answers a "OK- that's good - a lot of guys set that too tight."  One key piece of information that I was not sure of, Jim provided.  Set the ignition timing to 42 degrees BTDC as a starting point.  That tidbit probably made the whole conversation worthwhile; though any conversation with a living legend goes down as worthwhile in my book.

But, memorable conversation or not, it really did not solve my compression ratio problem. In fact it really narrowed it down to the "too deep" valve pockets on the pistons...

Now we come to the "don't try this at home" part of the title of this post.  It was far too late to consider having another set of custom pistons built, even if funds had been available for such a thing.  But out of the recesses of my mind, I managed to dredge up something that might be of value.  Some years ago Mike Roland mentioned to me that he had once welded up the domes on a set of pistons for a drag racer who was on a tight budget.  Hmmm.  Seemed that a consultation with the best welder I know might be in order.  John from PMFR informed me that as long as the pistons were not alloyed with silicone, I should be able to weld on them with no problem.  He further reassured me that I would be able to tell the moment I struck an arc - a silicone alloy piston would immediately result in massive amounts of black soot. 

Still, what would be worse?  Going to Bonneville with a motor down on compression, or missing another year because I screwed up the pistons?  It was about this time that I spent a Sunday afternoon watching "The World's Fastest Indian" again; just for a little inspiration.  The more I pondered old Burt Munro casting his own pistons in the little shack he lived and worked in, the more I knew I had to give it a shot.  Besides, the ceramic coatings I planned to use on the piston domes should give a little extra protection.

That's not to say I wasn't still plenty nervous about it.  What if I managed to distort the ring lands?  What if I screwed up in some other unforeseen manner?  And what might that unforeseen screw up be?  Obviously no point in pursuing that line of thought.  If I could come up with a possible screw up, it would not be unforeseen.

To make a long story short, the pistons welded very nicely.  In fact a steadier hand on my part would have resulted in a nice looking job.  But, despite the lack of beauty in my welding, I was confident that it was structurally sound - well...at least as structurally sound as one can be when welding a piece that normal people would not consider mistreating in such a way.  So, back to the mill to re-cut the valve pockets to a minimum depth, and then mock up with clay once again.  With only a minimum of frustration I achieved valve to piston clearances of an acceptable distance.


Welded

Machined after Welding

Back to the same old drill of cc'ing the newly larger piston domes and entering the results into the computer.  To be honest, by that point in time I would have been happy to see 9:1, so I was quite pleased to find we were up to 9.8:1!  Next up: balancing the flywheels.

Thursday, July 26, 2012

EL Bonnie, Part 2: Never Easy

In my last post on EL Bonnie, I stated that the next step would be to mock the engine up to check/blueprint the breather timing. As is so often the case, easier said than done! My intention was to perform this quick and dirty, without regard to cam bushing clearances, but no such luck. I knew that I was dealing with an inferior aftermarket cam cover, and so at some point the bushings would need to be replaced and line reamed for proper fitment, but I thought I could get by with them for now.  The lineage of the cover was quite evident.  A certain company who will remain nameless to protect the guilty, reproduces these covers and puts them on their reproduction Knucklehead motors.  I have seen one other in the past; it too had damage to the bushings from misalignment.  One has to wonder how big a hammer it took to get one of these covers installed the first time.  It seems that S&S made the right call in casting their name into the covers they make, if for no other reason than to keep them from being mistaken for these gems. 

Did I mention that this motor is being done on a budget?  It has much in common with something I would build for myself in that respect; a lot of "spare parts" coming together,  in some cases those parts finding their way to the build based on availability and price rather than on fitness.

Before assembling the case halves for the mock up, I put the cam into the gearcase with the cam cover to ascertain how much it bound up in the bushings- the answer being plenty! Still thinking I could get this done quickly, I chose to line ream the cover bushing an extra couple thousands (the particular reamer I use for this operation is adjustable) since that would surely alleviate the bind and keep things moving. Wrong again! Apparently even the additional clearance was not enough to compensate for the mis-alignment between the case and cover. Time to re- think this.

After an appropriate bit of soul searching (to make the decision sound infinitely more dramatic than it actually was) it appeared to be the perfect opportunity to follow the old adage; when life gives you lemons, make lemonade!

The cam choices available are a (new) old Sifton 110 or an S&S FHP 420.  Both of them happen to be set up for a Torrington needle bearing in the crankcase rather than a bushing (the shaft for a Torrington will be approximately .0007" larger O.D. than one for a bushing).  That means that either the crankcase cam bushing would need to be reamed oversize (the original cam bushing had enough wear that it already fit) or the case would need to be bored for the larger outer diameter of the Torrington.  The bearing would have the added benefit of slightly less friction, so it seemed that the logical thing to do would be to use a Torrington on both ends of the cam.

Now, machining to install a bearing in the crankcase is pretty straight forward:  indicate in the existing hole and bore it to size.  The cover is an entirely different matter though, especially in this case, given there is good reason to suspect it was manufactured with the hole in the wrong place.  I decided to create a template.  I already had a 3/8" thick aluminum plate with the two dowel pin holes correctly located.  By installing the plate on the crankcase half and mounting it on the mill, I was able to indicate in the cam  bushing hole, and then going through the bushing hole, bore the aluminum plate. 


Indicating case bushing hole


Boring hole in template


Indicating template hole

Once I had a hole in the template, it was simply a matter of fabbing a couple extra dowel pins to align the cover to it.  Fortunately, at some point in the distant past I had built a fixture for holding generator cam covers level while installing and pinning bushings.  This made mounting the cover in the mill quick and easy.  Then, by indicating in the new hole in the template, I had the correct relationship between dowel pins and where the new cam bearing was to be installed.  BTW, the original hole in the cover checked as being only .006" off: I expected worse.


Boring cover for Torrington bearing

Once the new hole was bored and a bearings installed in both cover and case, another test fit with right case, cam and cover gave the results I was looking for: a totally free spinning cam!  Since I was in cam cover mode, I also tackled the pinion bushing.  I chose to go ahead and try installing a new bushing and line ream it, rather than going to extreme measures.  Kind of a "why go looking for trouble" approach, and in this case it paid off.  Another test fit with the cam cover bolted on the right case and the new S&S pinion shaft with bearings in place resulted in a very pleasant surprise.  Absolutely no binding even with only .0007" shaft to bushing clearance!  It appears that the cover manufacturer managed to get half of the bushing holes in the correct place.

Checking pinion shaft for binding

By the way, if any of those of you who are anxiously waiting for this motor are wondering, you may feel better knowing that the writing is lagging behind actual progress.

Saturday, July 14, 2012

EL Bonnie



Some of fellows from over Wisconsin way have been scheming for several years to put a 1939 61" (model EL) Knucklehead on the great salt flats of Utah - better known as Bonneville. Joe Taylor, the owner of the "project," is joined by Tom Anderson and John Endrizzi in the quest to take home a record in the 1000MPSVG class at the AMA sanctioned annual BUB Motorcycle Speed Trials. For those of you not quite up to speed on class designations (I fit in that category too) the 1000 refers to the maximum displacement in cubic centimeters - hence a 61 inch Knuckle = 1000cc. The MPS narrows it down further, to a frame that is Modified/Partial Streamlining. The final piece of the puzzle is the VG which stand for Vintage Gas, limiting the engine to a production date of 1955 or earlier.


The trio does not walk into this endeavor with no prior knowledge of what they are getting in to; Joe and Tom have previous Bonneville experience racing under the Buell Brothers banner. This build will, however, be their first foray into the vintage side of land speed racing.

As may be expected, a project like this is not without its setbacks. Too small budgets are almost always an issue when regular guys take something like this on. A major setback in this particular build was the untimely death of the engine builder. That will definitely put a damper on a project!


Knowing the predicament that the Buell Brothers found themselves in, I had to weigh my morbidly obese workload against the possibility of being involved in a record setting endeavor. In the end, the deciding factor was this: given my penchant for high performance and knuckleheads, how would I feel if EL Bonnie set a record, but another engine builder's name was associated with it? What could I do but offer my service to build the engine?

Before going any further, it is important to note that a project such as EL Bonnie would be virtually impossible to complete without the existence of a company such as S&S Cycle. S&S has made the commitment to reproduce quality engine parts for these early motors. Witness the parts in the shot below; all from S&S, and all vital to transforming this dream into a reality.





As soon as Joe dropped off the engine, it became apparent that they committed no sacrilege by turning it into a racer. Nearly every square inch of the '39 cases showed evidence of welding repairs. If they could talk, these cases would probably have quite a story to tell. With Joe's permission, I decided it would be worthwhile to do some reinforcement modifications. I added a gusset to the left side of the left front motor mount (which showed evidence of at least one previous repair). Early Knuckle cases are also known to be weak on the left side in the cylinder spigot area. My solution was to weld 3/8" plate to that area, windowed just enough to leave the serial number pad intact.

Moving on to the the inside of the cases, windage is always a concern - at least to my mind. The "pocket" in the right side case quite obviously performs no function other than to save a bit of aluminum during the casting process, and I have always pondered what to do with it. What, if any, effect on windage this pocket has is any one's guess. On the other hand, when it comes to racing, I am a firm believer that the difference can often come down to a matter of adding together all the details. I've heard it before: "Do you really think that will make a difference?" My answer is usually, "We'll see." But the more honest answer is no ....but hopefully when it is added to the other dozen things that are too small to make a difference by themselves, it will!

A couple of thin aluminum plates cut to fit and welded into place smooth out the interior of the right case half. The next step toward minimizing windage was to polish the interior of the cases, including the gearcase. One of the final steps before final assembly on the case will be to treat them with TLTD, a oil shedding thermal dispersant coating.






Now you see it ...





Now you don't



So, if all the previous repairs had not distorted the cases, it was a good bet that with the welding I did, there was reason for concern! Besides, one of the keys to making this motor fast will be to keep the friction losses as low as possible. The first step to ensuring that was to mount the left case to the mill and indicate in the pinion shaft race hole (races removed). Once the indicator showed that it was centered in the hole, I gently installed the right case, torquing all the case bolts. Taking a reading from the indicator in the right side case race hole, I was far from shocked to find .012" runout. A +.025 race in the right case was the cure.




Next, with the cases still bolted together, I decked the bottoms of the motor mounts enough to insure they are true, and then did the same with the cylinder mounting surfaces. Before giving the mill the rest of the day off, I also machined the breather gear bore for the +.030 S&S gear, removing 70 years worth of damage in the process. Installation of the new crankcase races, and line lapping them to size pretty well brings us up to the present. Next is a mock up to blueprint the breather opening in the case and see what kind of piston deck height we are dealing with. To be continued ...

Sunday, July 1, 2012

Christ, the Church, and Marriage

Wives, submit yourselves unto your own husbands, as unto the Lord. For the husband is the head of the wife, even as Christ is the head of the church: and he is the saviour of the body. Therefore as the church is subject unto Christ, so let the wives be to their own husbands in every thing. Husbands, love your wives, even as Christ also loved the church, and gave himself for it; That he might sanctify and cleanse it with the washing of water by the word, That he might present it to himself a glorious church, not having spot, or wrinkle, or any such thing; but that it should be holy and without blemish. So ought men to love their wives as their own bodies. He that loveth his wife loveth himself. For no man ever yet hated his own flesh; but nourisheth and cherisheth it, even as the Lord the church: For we are members of his body, of his flesh, and of his bones. For this cause shall a man leave his father and mother, and shall be joined unto his wife, and they two shall be one flesh. This is a great mystery: but I speak concerning Christ and the church. Ephesians 5:22-32 (emphasis added)

As shown at the end of the above passage, marriage is a symbol or picture of Christ and his relationship with the church. That would seem to help explain why there are so many dead set on destroying that symbol today. This passage in Ephesians is given to help us understand Christ's relationship to the church by holding up a biblical marriage as an example. Sadly, in the wicked world in which we live, the average marriage bears little resemblance to what scripture tells us it should look like. Still much truth about the nature of the church can be found here, such as Christ is the head and the church is subject to him. Christ loves the church and gave himself for it. He uses the word of God to clean and sanctify the church to make it holy, and even that there is an intimacy between Christ and the church that will be found only in that relationship.

If you are a Christian, this should lead you to a couple of conclusions. One is that your own marriage should reflect the values presented in Ephesians 5 so that it does not present a distorted image of Christ and the church to the world. The second conclusion a Christian should draw is that the church they belong to also should reflect the values presented in Ephesians 5 in it's relationship to Christ, so that it does not present a distorted image of marriage to the world.

Friday, June 8, 2012

126 Drag Motor - Another Update

Well, it seems that I have neglected to take as many pictures as I might have, but the engine has actually progressed since the last installment. A mock up to check valve to piston clearance revealed two things. The first was that the hunk of clay I have been using for probably 20 years for this purpose, has finally become just a little too hard. I read somewhere that plumbers putty also works well for this, and since I still had some left over from a drain repair last year, I gave it a try. Didn't like it. Even with a little grease on the valves, the putty didn't want to remain stuck to the piston. Happily, a call to my lovely wife caught her in the midst of shopping - what are the chances of that? Now I am the proud new owner of 99 cents worth of fresh Chinese made modeling clay! And yes; she did look for the American made version without luck.



The second thing that the mock up revealed was that the valve pockets in the pistons needed more clearance. The intake pockets were deep enough, but needed more radial clearance for the 2.125" diameter valves.




A trip to the mill took care of that, but the exhaust valves were another matter entirely. Not only did they not have enough valve to piston clearance, they actually touched the piston preventing a full revolution. This is a pretty unusual situation, and as such, it was unforeseen by me. And since it was unforeseen, I had already taken material from the inside of the piston domes to lighten them. Not knowing how much material would need to be removed from the valve pockets, but knowing I did not have much to work with, I chose to sink the exhaust valves deeper instead. I started by going .080" deeper to see if that gave at least some clearance (and it did), and then went back and cut the seats again to give a finished clearance of .100". A new pair of custom exhaust valves with shorter overall length have been ordered to put the stem protrusion back into a rocker geometry friendly state. Incidentally, the exhaust pockets also needed a little more radial clearance than they came with, despite the fact that I did not increase the exhaust valve size.

As I hinted at in my last post, the flywheels were cut down a fairly radical amount, making the balance trickier than usual. Normally when balancing flywheels, the counterweight section of the flywheel is the heavy spot, and one simply drills holes at the heavy spot to bring it into balance. When the flywheels start to get very narrow, the "counterweight" shrinks. With big bore pistons it is easy to come up with a situation where the "heavy" spot in balancing is on the crankpin side - not the place you want to weaken by drilling balance holes. After I had lightened the pistons as much as I felt was safe, that was still the situation I was faced with. Rather than creating a "swiss cheese" effect in the crankpin area of the flywheels, however, I used an end mill to "skim" the required weight. After multiple trips between the mill and the balance table, the flywheels came into balance with no holes drilled whatsoever. Sorry, but I neglected to take pictures.


As for the rest of the motor, the inside of the crankcases (including gearcase) were treated to an oil shedding coating, as were the flywheels once the balancing was complete. Again, I neglected to take pictures.


Once trued, the flywheels were installed in cases and the oil pump and gearcase assembled. As I await delivery on the custom exhaust valves, final porting work is the next order of business. The intake ports, as mentioned in a previous post, have had the floors welded up. Due to the large valve size (2.125" vs. the 2.0" the heads came with) a larger port opening size was in order. The port diameter that I chose was 1.900" (89% of the valve diameter). This of course required major modifications to the intake manifold, which included relocating the flange bolts. I will try to include some pictures when the heads are nearer completion.


Fortunately the owner gave me a bit of a reprieve on finishing up this motor, which has been a real blessing since I have a boatload of other work that needs to be finished up soon, not the least of which is a motor that is headed for the great salt flats dyno in Utah. Now, with that "teaser" I had better abandon the keyboard for more productive endeavors.